Nissan Altima L32. Instruction — part 917
LU-14
< ON-VEHICLE REPAIR >
[QR25DE]
OIL PUMP
• Install the inner rotor and outer rotor with the punched marks on
the oil pump cover side.
CAUTION:
Before assembly apply new engine oil to the parts as speci-
fied.
PBIC0255E
OIL COOLER
LU-15
< ON-VEHICLE REPAIR >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
OIL COOLER
Removal and Installation
INFOID:0000000004202502
WARNING:
Be careful not to get burned, engine coolant and engine oil may be hot.
CAUTION:
• When removing oil cooler, prepare a shop cloth to absorb any engine oil leakage or spillage.
• Completely wipe off any engine oil that adheres to the engine and the vehicle.
REMOVAL
1. Drain engine oil. Refer to
2. Drain engine coolant. Refer to
CO-12, "Changing Engine Coolant"
CAUTION:
Do not spill coolant on the drive belt.
3. Disconnect water hoses from oil cooler.
NOTE:
For reference during installation, put matching marks on oil cooler hoses.
4. Remove oil cooler.
INSPECTION AFTER REMOVAL
1. Check oil cooler for cracks.
2. Check oil cooler for clogging by blowing through coolant inlet. If necessary, replace oil cooler assembly.
INSTALLATION
Installation is in the reverse order of removal.
ALBIA0538GB
1.
Oil pressure switch
2.
Oil cooler
3.
Gasket
4.
Water hose (outlet)
5.
Water hose (inlet)
A.
To water control valve housing
B.
To heater pipe assembly
C.
Hose clamp
D.
Clip
LU-16
< ON-VEHICLE REPAIR >
[QR25DE]
OIL COOLER
• Remove any old liquid gasket adhering to the oil pressure switch and oil cooler before installing the oil pres-
sure switch.
INSPECTION AFTER INSTALLATION
Start engine and check for leaks of engine oil or coolant.
SERVICE DATA AND SPECIFICATIONS (SDS)
LU-17
< SERVICE DATA AND SPECIFICATIONS (SDS)
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Oil Pressure
INFOID:0000000004202503
Oil Pump
INFOID:0000000004202504
Unit: mm (in)
Regulator Valve
INFOID:0000000004202505
Unit: mm (in)
Oil Capacity
INFOID:0000000004202506
Unit: (US qt, Imp qt)
Engine speed
rpm
Approximate discharge pressure
kPa (kg/cm
2
, psi)
Idle speed
More than 98 (1.0, 14)
2,000
294 (3.0, 43)
6,000
392 (4.0, 57)
Body to outer rotor radial clearance
0.114 - 0.179 (0.0045 - 0.0070)
Inner rotor to outer rotor tip clearance
0.170 - 0.220 (0.0067 - 0.0087)
Body to inner rotor axial clearance
0.030 - 0.070 (0.0012 - 0.0028)
Body to outer rotor axial clearance
0.060 - 0.110 (0.0024 - 0.0043)
Inner rotor to brazed portion of housing clearance
0.035 - 0.070 (0.0014 - 0.0028)
Regulator valve to oil pump cover clearance
0.040 - 0.097 (0.0016 - 0.0038)
Drain and refill
With oil filter change
Approximately 4.6 (4 7/8, 4)
Without oil filter change
Approximately 4.3 (4 1/2, 3 3/4)
Dry engine (engine overhaul)
Approximately 5.4 (5 3/4, 4 3/4)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст