Nissan Terrano model r20 series 2004. Instruction — part 292
Coil Spring Shock Absorber
REMOVAL AND INSTALLATION
I
Refer to Removal and Installation of REAR AXLE AND REAR
SUSPENSION, RA-12.
When installing coil spring and lower spring seat, pay atten-
tion to its direction.
Be sure spring rubber seat is not twisted and has not slipped
off when installing coil spring.
INSPECTION
I
Check coil spring for yield, deformation or cracks.
I
Check coil spring specifications. Refer to SDS, RA-16.
I
Check shock absorber for oil leakage, cracks or deformation.
I
Check shock absorber specifications. Refer to SDS, RA-16.
I
Check all rubber parts for wear, cracks or deformation. Replace
if necessary.
Upper Link, Lower Link and Panhard Rod
INSPECTION
Check for cracks, distortion or other damage. Replace if necessary.
BUSHING REPLACEMENT
Check for cracks or other damage. Replace with suitable tool if
necessary.
I
Remove bushing with suitable tool.
When installing bushing, apply a coating of 1% soap water to
outer wall of bushing.
Always install new bushing.
Do not tap end face of bushing directly with a hammer.
SRA910
SRA898
SRA900
REAR SUSPENSION
RA-14
INSTALLATION
When installing each link, pay attention to direction of bolts
and nuts. Refer to REAR SUSPENSION - Components, RA-13.
When installing each rubber part, final tightening must be car-
ried out under unladen condition with tires on ground.
Stabilizer Bar
REMOVAL AND INSTALLATION
I
When removing and installing stabilizer bar, fix portion A.
SRA909
REAR SUSPENSION
Upper Link, Lower Link and Panhard Rod
(Cont’d)
RA-15
General Specifications
COIL SPRING AND SHOCK ABSORBER
Model
Hardtop
Wagon
Coil spring
Wire diameter
mm (in)
13.0 (0.512)
13.5 (0.531)
Free length
mm (in)
400 (15.75)
417 (16.42)
Spring constant
N/mm (kg/mm, lb/in)
25.5 (2.6, 146)
29 (3.0, 168)
Shock absorber
Shock absorber type
Non-adjustable (hydraulic)
Maximum length mm (in)
586 (23.07)
596 (23.46)
Minimum length mm (in)
350 (13.78)
356 (14.02)
Damping force
[at 0.3 m (1.0 ft)/sec.]
N (kg, lb)
Expansion
990 - 1,330
(101 - 136,
223 - 229)
1,169 - 1,563
(119 - 159,
223 - 351)
Compression
346 - 524
(35.3 - 53.4,
77.8 - 117.8)
301 - 461
(30.7 - 47.0,
67.7 - 103.6)
RA260
STABILIZER BAR
Model
Hardtop
Wagon
Diameter
mm (in)
23 (0.91)
24 (0.94)
Spring constant
N/mm (kg/mm, lb/in)
24.5 (2.5, 140)
29.0 (3.0, 166)
Inspection and Adjustment
WHEEL BEARING
Total end play
mm (in)
0 (0)
SERVICE DATA AND SPECIFICATIONS (SDS)
RA-16
BRAKE SYSTEM
CONTENTS
Supplement Restraint System (SRS)
. . . . . . .3
Precautions . . . . . . . . . . . . . . . . ..3
Preparation . . . . . . . . . . . . . . . . ..4
. . . . . . . . . . ..5
Checking Brake Fluid Level. . . . . . . . . . .5
Checking Brake Line . . . . . . . . . . . . ...5
Changing Brake Fluid . . . . . . . . . . . . ..5
Brake Burnishing Procedure. . . . . . . . . . 5
. . . . . . . . . . . .6
Bleeding Brake System . . . . . . . . . . . ...8
Removal. . . . . . . . . . . . . . . . . ...9
Inspection. . . . . . . . . . . . . . . . . .9
Installation. . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . ...10
Removal and Installation . . . . . . . . . . ...10
Removal. . . . . . . . . . . . . . . . . . 11
Installation. . . . . . . . . . . . . . . . .. 11
Inspection and Adjustment . . . . . . . . . . 12
. . . . . . . . ..14
Removal and Installation . . . . . . . . . . ...14
Removal. . . . . . . . . . . . . . . . . .15
Installation. . . . . . . . . . . . . . . . ..15
Inspection. . . . . . . . . . . . . . . . ...15
Adjustment . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . .17
Removal. . . . . . . . . . . . . . . . . .17
Installation. . . . . . . . . . . . . . . . ..17
. . . . . . . . . . . . . . 18
Removal and Installation . . . . . . . . . . ...18
Inspection. . . . . . . . . . . . . . . . ...18
Installation. . . . . . . . . . . . . . . . ..19
. . . . . . . . . . . . . . . .20
Removal and Installation . . . . . . . . . . ...20
Inspection. . . . . . . . . . . . . . . . ...22
VACUUM PUMP (TD27Ti engine model)
. . . . . 24
Removal and Installation . . . . . . . . . . ...24
Inspection. . . . . . . . . . . . . . . . ...24
VACUUM PUMP (ZD30DDTi engine model)
. . . ...26
Removal and Installation . . . . . . . . . . ...26
. . . . . . . . . . . . ...27
Pad Replacement . . . . . . . . . . . . . ..27
Removal. . . . . . . . . . . . . . . . . .28
Disassembly. . . . . . . . . . . . . . . ...28
Inspection. . . . . . . . . . . . . . . . ...28
Assembly . . . . . . . . . . . . . . . . ...29
Inspection. . . . . . . . . . . . . . . . ...29
Installation. . . . . . . . . . . . . . . . ..31
. . . . . . . . . . . . ...32
Removal. . . . . . . . . . . . . . . . . .33
Shoe Replacement . . . . . . . . . . . . . 34
Inspection. . . . . . . . . . . . . . . . ...34
Installation. . . . . . . . . . . . . . . . ..34
. . . . . . . . . ..36
Removal and Installation . . . . . . . . . . ...36
Inspection. . . . . . . . . . . . . . . . ...36
Adjustment . . . . . . . . . . . . . . . . .36
. . . . . . . . . ..38
Purpose. . . . . . . . . . . . . . . . . ..38
Operation . . . . . . . . . . . . . . . . ...38
ABS Hydraulic Circuit . . . . . . . . . . . . 38
System Description. . . . . . . . . . . . . 39
Removal and Installation . . . . . . . . . . ...43
. . . . . . . . . . . ...48
How to Perform Trouble Diagnoses for Quick
and Accurate Repair . . . . . . . . . . . . ..48
Component Parts and Harness Connector
Location . . . . . . . . . . . . . . . . . .49
Circuit Diagram for Quick Pinpoint Check. . . . .50
Wiring Diagram - ABS - . . . . . . . . . . . .51
CONSULT-II . . . . . . . . . . . . . . . ...59
CONSULT-II Inspection Procedure. . . . . . . 60
Preliminary Check. . . . . . . . . . . . . ..66
Ground Circuit Check . . . . . . . . . . . . 67
Diagnostic Procedure 1 (Not self-diagnostic item). 68
Diagnostic Procedure 2 (Warning lamp stays on
when ignition switch is turned ON). . . . . . . 70
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст