Nissan Terrano model r20 series 2004. Instruction — part 24
Connecting Rod . . . . . . . . . . . . . . .91
Crankshaft. . . . . . . . . . . . . . . . ..92
Available Main Bearing. . . . . . . . . . . ..92
Available Connecting Rod Bearing. . . . . . . 93
Miscellaneous Components. . . . . . . . . ...94
TD27Ti
. . . . . . . . . . . . . . . .95
Parts Requiring Angular Tightening. . . . . . ...95
Liquid Gasket Application Procedure . . . . . . 95
. . . . . . . . . . . . . . . ..96
Special Service Tools . . . . . . . . . . . . 96
Commercial Service Tools . . . . . . . . . . .99
ENGINE COMPONENTS - Outer Parts
. . . . . .100
ENGINE COMPONENTS - Internal Parts
. . . . ..102
Measurement of Compression Pressure. . . . .103
. . . . . . . . . . . . . . 104
Removal. . . . . . . . . . . . . . . . ...105
Disassembly. . . . . . . . . . . . . . . .106
Inspection. . . . . . . . . . . . . . . . .107
Assembly . . . . . . . . . . . . . . . . . 113
Installation. . . . . . . . . . . . . . . . 114
. . . . . . . . . . 117
. . . . . . . . . . . . . ... 119
Removal and Installation . . . . . . . . . . . 119
Inspection. . . . . . . . . . . . . . . . . 119
. . . . . . . . . . . . . .123
. . . . . . . . . . . . ..125
Disassembly. . . . . . . . . . . . . . . .125
Inspection. . . . . . . . . . . . . . . . .127
Assembly . . . . . . . . . . . . . . . . .138
SERVICE DATA AND SPECIFICATIONS (SDS)
. . 143
General Specifications. . . . . . . . . . . .143
Inspection and Adjustment . . . . . . . . . ..144
CONTENTS
(Cont’d)
EM-2
Parts Requiring Angular Tightening
I
Use an angle wrench for the final tightening of the cylinder head
bolts.
I
Do not use a torque value for final tightening.
I
The torque value for these parts are for a preliminary step.
I
Ensure thread and seat surfaces are clean and coated with
engine oil.
Liquid Gasket Application Procedure
1. Use a scraper to remove old liquid gasket from mating
surfaces and grooves. Also, completely clean any oil from
these areas.
2. Apply a continuous bead of liquid gasket to mating sur-
faces. (Use Genuine Liquid Gasket or equivalent.)
I
Be sure liquid gasket diameter is as specified.
3. Apply liquid gasket around the inner side of bolt holes
(unless otherwise specified).
4. Assembly should be done within 5 minutes after coating.
5. Wait at least 30 minutes before refilling engine oil and
engine coolant.
SEM164F
AEM080
PRECAUTIONS
ZD
EM-3
Special Service Tools
Tool number
Tool name
Description
ST0501S000
Engine stand assembly
q
1
ST05011000
Engine stand
q
2
ST05012000
Base
NT042
Disassembling and assembling
KV10106500
Engine stand shaft
NT028
KV11106101
Engine sub-attachment
NT819
KV10115600
Valve oil seal drift
NT603
Installing valve oil seal
Use side A.
Side A
a: 20 (0.79) dia.
b: 13 (0.51) dia.
c: 10.3 (0.406) dia.
d: 8 (0.31) dia.
e: 10.7 (0.421)
f: 5 (0.20)
Unit: mm (in)
KV10107902
Valve oil seal puller
q
1
KV10116100
Valve
oil
seal
puller
adapter
NT605
Removing valve oil seal
KV101056S0
Ring gear stopper
q
1
KV10105630
Adapter
q
2
KV10105610
Plate
NT617
Preventing crankshaft from rotating
a: 3 (0.12)
b: 6.4 (0.252)
c: 2.8 (0.110)
d: 6.6 (0.260)
e: 107 (4.21)
f: 14 (0.55)
g: 20 (0.79)
h: 14 (0.55) dia.
Unit: mm (in)
PREPARATION
ZD
EM-4
Tool number
Tool name
Description
KV101151S0
Lifter stopper set
q
1
KV10115110
Camshaft pliers
q
2
KV10115120
Lifter stopper
NT041
Changing shims
KV101092S0
Valve spring compressor
q
1
KV10109210
Compressor
q
2
KV10109220
Adapter
NT718
Disassembling and assembling valve compo-
nents
ED19600620
Compression gauge adapter
NT820
Checking compression pressure
ST16610000
Pilot bushing puller
NT045
Removing crankshaft pilot bushing
KV10111100
Seal cutter
NT046
Removing steel oil pan and rear timing chain
case
WS39930000
Tube presser
NT052
Pressing the tube of liquid gasket
KV10112100
Angle wrench
NT014
Tightening bolts for bearing cap, cylinder head,
etc.
PREPARATION
ZD
Special Service Tools (Cont’d)
EM-5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст