Nissan Murano Z51. Instruction — part 1234
SE-124
< REMOVAL AND INSTALLATION >
REAR SEAT
4.
Install the rear seat mounting bolt on the reclining device exten-
sion bracket.
5.
Install the rear seat mounting bolt and on the seat cushion
hinge.
6.
Connect the seatback control cable.
7.
Install the seat cushion hinge cover.
8.
Install the reclining cover.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• When removing and installing, 2 workers are required so as to prevent it from dropping.
• Before installation, check that the rear seat harness and seatback control cable is not pressed by
seat frame.
Disassembly and Assembly
INFOID:0000000005518239
SEATBACK
Disassembly
1.
Remove the armrest. (RH seat only)
• Remove the armrest outer cover.
JMJIA1684ZZ
JMJIA1685ZZ
: Pawl
JMJIA1470ZZ
REAR SEAT
SE-125
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the armrest mounting bolts (A), and then slide the
armrest to toward the arrow direction.
2.
Separate the seatback assembly and seat cushion assembly.
• Disconnect the seat cushion heater unit harness connectors
(A) and remove the harness clamps. (with heater seat model
only)
• Remove the seat cushion link cover.
• Remove the mounting bolt (A), and then separate the seat-
back assembly and seat cushion assembly.
JMJIA1471ZZ
JMJIA1438ZZ
JMJIA1439ZZ
JMJIA1440ZZ
SE-126
< REMOVAL AND INSTALLATION >
REAR SEAT
3.
Remove the mounting screw (A), and then remove the reclining
device outer cover.
4.
Remove the mounting screws (A), and then remove the reclining
device inner cover (outside). (LH seat)
5.
Remove the seatback trim and pad.
• Remove the clips, and then pull out the seatback board.
• Remove the seatback trim fixing hog rings and retainer.
• Remove the headrest holder.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
• Remove the seatback trim and pad from seatback frame.
• Remove the hog rings to separate the seatback trim and seat-
back pad.
6.
Remove the seatback silencer.
JMJIA1441ZZ
JMJIA1442ZZ
: Clip
JMJIA1443ZZ
PIIB4084J
REAR SEAT
SE-127
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
7.
Remove the screws (A), and then remove the reclining device
inner cover (outside). (RH seat)
8.
Remove the screw (A), and then remove the reclining device
inner cover (inside).
9.
Remove the mounting bolts (A), and then remove the seatback
frame from reclining device assembly.
10. Remove the mounting nuts (A), and then remove the dynamic
dumper. (With top road sunroof model only)
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the seatback frame.
SEAT CUSHION
Disassembly
1.
Remove the armrest. (RH seat only)
JMJIA1444ZZ
JMJIA1445ZZ
JMJIA1446ZZ
JMJIA1447ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст