Nissan Murano Z51. Instruction — part 1306
CRASH ZONE SENSOR
SR-49
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CRASH ZONE SENSOR
Exploded View
INFOID:0000000005518932
Removal and Installation
INFOID:0000000005518933
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove the radiator cover grill (RH). Refer to
2.
Remove the air duct (inlet). Refer to
3.
Remove the crash zone sensor fixing nuts.
4.
Disconnect the crash zone sensor harness connector, and then remove the crash zone sensor.
CAUTION:
• Never impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact.
• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air
bag.
INSTALLATION
Install in the reverse order of removal.
1.
Crash zone sensor
A.
Crash zone sensor harness connec-
tor
Refer to
for symbols in the figure.
JMHIA0515GB
JMHIA0009ZZ
SR-50
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
CRASH ZONE SENSOR
CAUTION:
• Never use the old fixing nuts after removal, replace with the new nuts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
SIDE AIR BAG (SATELLITE) SENSOR
SR-51
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE AIR BAG (SATELLITE) SENSOR
Exploded View
INFOID:0000000005518934
Removal and Installation
INFOID:0000000005518935
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove the front seat belt. Refer to
SB-7, "SEAT BELT RETRACTOR : Removal and Installation"
2.
Remove the side air bag (satellite) sensor fixing nuts.
3.
Disconnect the side air bag (satellite) sensor harness connector, and then remove the side air bag (satel-
lite) sensor.
CAUTION:
• Never impact the side air bag (satellite) sensor.
• Replace the side air bag (satellite) sensor if it has been
dropped or sustained an impact.
• Replace the side air bag (satellite) sensor of deployed SRS front side air bag module and deployed
SRS side curtain air bag module.
INSTALLATION
1.
Side air bag (satellite) sensor
A.
Side air bag (satellite) sensor har-
ness connector
Refer to
for symbols in the figure.
JMHIA0516GB
JMHIA0009ZZ
SR-52
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
SIDE AIR BAG (SATELLITE) SENSOR
Install in the reverse order of removal.
CAUTION:
• Never use the old fixing nuts after removal, replace with the new nuts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст