Nissan Murano Z51. Instruction — part 1522
WT-26
< DTC/CIRCUIT DIAGNOSIS >
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
CAUTION:
Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.
Is the inspection result normal?
YES
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
NO
>> GO TO 1.
Special Repair Requirement
INFOID:0000000005575986
1.
CHECK TIRE PRESSURE
Check all tires for tire pressures. Refer to
.
Does all tire pressure data meet the specification?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
2.
PERFORM ID REGISTRATION
Perform ID registration. Refer to
WT-22, "ID REGISTRATION PROCEDURE : Special Repair Requirement"
.
>> END
C1708, C1709, C1710, C1711 TRANSMITTER
WT-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1708, C1709, C1710, C1711 TRANSMITTER
DTC Logic
INFOID:0000000005575987
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1708”, “C1709”, “C1710”, “C1711” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005575988
1.
CHECK TIRE PRESSURE SIGNAL
With CONSULT-III
1.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
CAUTION:
Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.
Is a tire pressure of 0 kPa (0 Psi) displayed for all wheels?
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector and tire pressure receiver harness connector.
3.
Check the continuity between BCM harness connector and tire pressure receiver harness connector.
DTC
Display item
Malfunction detected condition
Possible cause
C1708
[NO DATA] FL
Tire pressure data signal from the front left wheel
transmitter cannot be detected.
• Harness or connector
(Tire pressure receiver, BCM)
• ID registration is not finished
• Transmitter malfunction
• BCM malfunction
C1709
[NO DATA] FR
Tire pressure data signal from the front right wheel
transmitter cannot be detected.
C1710
[NO DATA] RR
Tire pressure data signal from the rear right wheel
transmitter cannot be detected.
C1711
[NO DATA] RL
Tire pressure data signal from the rear left wheel
transmitter cannot be detected.
Monitor item
Condition
Displayed value
AIR PRESS FL
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or
more, then drive normally for 10 minutes.
Internal pressure of tires
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
WT-28
< DTC/CIRCUIT DIAGNOSIS >
C1708, C1709, C1710, C1711 TRANSMITTER
4.
Check the continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK TIRE PRESSURE RECEIVER POWER SUPPLY CIRCUIT
1.
Connect the BCM harness connector.
2.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
3.
Check the voltage between the BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK TIRE PRESSURE RECEIVER
Check tire pressure receiver. Refer to
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace tire pressure receiver. Refer to
WT-59, "Removal and Installation"
5.
CHECK ID REGISTRATION
Perform ID registration of all transmitters. Refer to
WT-22, "ID REGISTRATION PROCEDURE : Special
.
Can ID registration of all transmitters be completed?
YES
>> GO TO 6.
NO
>> Replace transmitter. Refer to
.
6.
CHECK TIRE PRESSURE MONITORING SYSTEM
With CONSULT-III
1.
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M21
1
Existed
138
4
139
2
BCM
—
Continuity
Connector
Terminal
M123
137
Ground
Not existed
138
139
BCM
—
Voltage
Connector
Terminal
M123
138
Ground
5 V
C1708, C1709, C1710, C1711 TRANSMITTER
WT-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
CAUTION:
Stop the vehicle and within 15 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of
“BCM” to read the tire pressure for all wheels.
Is the inspection result normal?
YES
>> Replace the DTC-detected malfunctioning transmitter. Refer to
NO
>> Replace BCM. Refer to
.
Special Repair Requirement
INFOID:0000000005575989
1.
CHECK TIRE PRESSURE
Check all tires for tire pressures. Refer to
.
Does all tire pressure data meet the specification?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
2.
PERFORM ID REGISTRATION
Perform ID registration. Refer to
WT-22, "ID REGISTRATION PROCEDURE : Special Repair Requirement"
>> END
Monitor item
Condition
Displayed value
AIR PRESS FL
Drive at a speed of 40 km/h (25 MPH) or more, for several
minutes without stopping.
Internal pressure of tires
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст