Nissan Silvia. Instruction — part 68
SAT523GA
2.
Install accumulator piston.
a.
Install O-rings onto accumulator piston.
I
Apply ATF to O-rings.
Accumulator piston O-rings
Unit: mm (in)
Accumulator
A
B
C
D
Small diameter end
29 (1.14)
32 (1.26)
45 (1.77)
29 (1.14)
Large diameter end
45 (1.77)
50 (1.97)
50 (1.97)
45 (1.77)
SAT938A
b.
Install return spring for accumulator A onto transmission case.
Free length of return spring:
Refer to SDS, AT-289.
SAT939AA
c.
Install accumulator pistons A, B, C and D.
I
Apply ATF to transmission case.
SAT941A
3.
Install band servo piston.
a.
Install return springs onto servo piston.
SAT942A
b.
Install band servo piston onto transmission case.
I
Apply ATF to O-ring of band servo piston and transmis-
sion case.
c.
Install gasket for band servo onto transmission case.
GI
MA
EM
LC
EC
FE
CL
MT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Assembly (1) (Cont’d)
AT-269
SAT940A
d.
Install band servo retainer onto transmission case.
SAT943AA
4.
Install rear side clutch and gear components.
a.
Place transmission case in vertical position.
SAT944A
b.
Slightly lift forward clutch drum assembly. Then slowly rotate it
clockwise until its hub passes fully over clutch inner race inside
transmission case.
SAT945A
c.
Check to be sure that rotation direction of forward clutch
assembly is correct.
SAT946A
d.
Install thrust washer onto front of overrun clutch hub.
I
Apply petroleum jelly to the thrust washer.
I
Insert pawls of thrust washer securely into holes in over-
run clutch hub.
ASSEMBLY
Assembly (1) (Cont’d)
AT-270
SAT947A
e.
Install overrun clutch hub onto rear internal gear assembly.
SAT948A
f.
Install needle bearing onto rear of overrun clutch hub.
I
Apply petroleum jelly to needle bearing.
SAT949A
g.
Check that overrun clutch hub rotates as shown while holding
forward clutch hub.
SAT950A
h.
Place transmission case into horizontal position.
SAT951A
i.
Install rear internal gear, forward clutch hub and overrun clutch
hub as a unit onto transmission case.
GI
MA
EM
LC
EC
FE
CL
MT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Assembly (1) (Cont’d)
AT-271
SAT952A
j.
Install needle bearing onto rear internal gear.
I
Apply petroleum jelly to needle bearing.
SAT953A
k.
Install bearing race onto rear of front internal gear.
I
Apply petroleum jelly to bearing race.
I
Securely engage pawls of bearing race with holes in front
internal gear.
SAT954A
l.
Install front internal gear on transmission case.
SAT216B
5.
Install output shaft and parking gear.
a.
Insert output shaft from rear of transmission case while slightly
lifting front internal gear.
I
Do not force output shaft against front of transmission
case.
SAT957A
b.
Carefully push output shaft against front of transmission case.
Install snap ring on front of output shaft.
I
Check to be sure output shaft cannot be removed in rear
direction.
ASSEMBLY
Assembly (1) (Cont’d)
AT-272
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст