Nissan Pathfinder (2007 year). Instruction — part 250
DRIVE SHAFT
FAX-7
C
E
F
G
H
I
J
K
L
M
A
B
FAX
2007 Pathfinder
DRIVE SHAFT
PFP:39100
Removal and Installation
EDS003AD
REMOVAL
1.
Remove wheel and tire using power tool.
2.
Remove rear engine under cover using power tool.
3.
Remove wheel sensor harness from mount on knuckle, then disconnect wheel sensor harness connector.
CAUTION:
Do not pull on wheel sensor harness.
4.
Remove wheel hub and bearing assembly. Refer to
FAX-5, "Removal and Installation"
.
●
It is not necessary to remove wheel sensor from wheel hub when wheel hub is not being replaced.
●
Carefully feed wheel sensor harness through hole in splash shield.
5.
Separate upper link ball joint stud from steering knuckle using
Tool.
●
Support lower link with jack.
6.
Remove drive shaft assembly.
●
Pry drive shaft front final drive using suitable tool.
INSPECTION AFTER REMOVAL
●
Move joint up, down, left, right, and in axial direction. Check for any rough movement or significant loose-
ness.
●
Check boot for cracks or other damage, and for grease leakage.
●
If damaged, disassemble drive shaft to verify damage, and
repair or replace as necessary.
1.
Differential side oil seal
2.
Drive shaft
3.
Drive shaft lock nut
4.
Cotter pin
WDIA0341E
Tool number
: ST29020001 (J-24319-01)
WEIA0119E
SFA108A
FAX-8
DRIVE SHAFT
2007 Pathfinder
INSTALLATION
Installation is in the reverse order of removal.
●
When installing drive shaft onto front final drive, use Tool to pre-
vent damage to the oil seal while inserting drive shaft. Slide
drive shaft sliding joint and tap with a hammer to install securely.
CAUTION:
Never reuse the differential side oil seal.
●
Tighten wheel nuts to specification. Refer to
.
Disassembly and Assembly
EDS003AE
DISASSEMBLY
Final Drive Side
1.
Mount the drive shaft in a vise.
CAUTION:
When mounting the drive shaft in a vise, use copper or aluminum plates between the vise and the
drive shaft.
2.
Remove boot bands and slide the boot back.
3.
Put matching marks on housing and shaft before separating joint assembly.
CAUTION:
Use paint or similar substance for matching marks. Do not scratch the surfaces.
Tool number
: KV38105500 (J-33904)
SDIA2615E
1.
Circlip
2.
Dust cover
3.
Housing
4.
Snap ring
5.
Ball cage, steel ball and inner race assembly
6.
Stopper ring
7.
Boot band
8.
Boot
9.
Shaft
10.
Joint sub-assembly
WDIA0342E
DRIVE SHAFT
FAX-9
C
E
F
G
H
I
J
K
L
M
A
B
FAX
2007 Pathfinder
4.
Remove the stopper ring with a flat-bladed screwdriver as
shown, and pull the housing off.
5.
Remove the snap ring, then remove the ball cage, steel ball,
inner race assembly from the shaft.
6.
Remove the boot from the shaft.
7.
Remove circlip and dust cover from housing.
8.
Clean the old grease off of the housing using paper towels.
Wheel Side
1.
Mount the drive shaft in a vise.
CAUTION:
When mounting the drive shaft in a vise, use copper or aluminum plates between the vise and the
drive shaft.
2.
Remove the boot bands and slide the boot back.
3.
Screw a sliding hammer or suitable tool 30 mm (1.18 in) or more
into threaded part of joint sub-assembly. Pull joint sub-assembly
off of shaft as shown.
NOTE:
Align the sliding hammer and shaft and remove the joint sub-
assembly by pulling directly.
CAUTION:
●
If the joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace the entire drive
shaft assembly.
4.
Remove boot from the shaft.
5.
Remove circlip from the shaft.
6.
While rotating the ball cage, clean the old grease off of the joint sub-assembly using paper towels.
INSPECTION AFTER DISASSEMBLY
Shaft
●
Replace the shaft if there is any bending, cracking, or other damage.
Joint Sub-assembly
●
Check for any rough rotation or unusual axial looseness.
●
Clean any foreign material from inside the joint sub-assembly.
●
Check for any compression scars, cracks, or fractures.
CAUTION:
If any irregular conditions are found in the joint sub-assembly components, replace the entire joint
sub-assembly.
SFA476
SFA514A
SDIA0606E
FAX-10
DRIVE SHAFT
2007 Pathfinder
Housing
NOTE:
Housing, ball cage, steel ball, and inner race are in a set.
●
Check for any compression scars, cracks, fractures, or unusual wear on the ball rolling surface.
●
Check for any deformation of the boot installation components.
Ball Cage
●
Check the sliding surface for any compression scars, cracks, or fractures of sliding surface.
Steel Ball
●
Check for any compression scars, cracks, fractures, or unusual wear.
Inner Race
●
Check the ball sliding surface for any compression scars, cracks, or fractures.
●
Check for any damage to the serrated part.
ASSEMBLY
Final Drive Side
1.
Wrap the serrated part of the shaft with tape. Install the boot
band and boot to shaft.
NOTE:
Discard the old boot band and boot and use a new one for
assembly.
2.
Remove the tape wound around the serrated part of the shaft.
3.
Install the ball cage, steel ball, and inner race assembly on the
shaft, and secure them using the snap ring.
NOTE:
Discard the old snap ring and use a new one for assembly.
4.
Insert the specified quantity of Genuine NISSAN Grease or
equivalent, into the housing (indicated by * marks), and install it
onto shaft. Refer to
MA-11, "RECOMMENDED FLUIDS AND
.
5.
Install the stopper ring onto the housing.
CAUTION:
●
Do not reuse stopper rings.
●
Make sure that housing and stopper ring are fully engaged.
SFA800
SDIA1125E
Grease capacity
: 120
−
140 g (4.23
−
4.94 oz)
SDIA1446E
DRIVE SHAFT
FAX-11
C
E
F
G
H
I
J
K
L
M
A
B
FAX
2007 Pathfinder
6.
Install the boot securely into the grooves (indicated by * marks)
as shown.
CAUTION:
If there is grease on boot mounting surfaces (indicated by *
marks) of shaft and housing, boot may come off. Remove
all grease from surfaces.
7.
Check that the boot installation length “L” is the length indicated
below. Insert a flat-tip screwdriver or similar tool into the large
side of boot. Bleed air from boot to prevent boot deformation.
CAUTION:
●
The boot may break if the boot installation length is less than the specified value.
●
Do not to touch the tip of the screwdriver to the inside of the boot.
8.
Secure the big and small ends of the boot with the new boot
bands as shown.
NOTE:
Discard not reuse boot bands.
9.
Secure housing and shaft and then make sure that they are in the correct position when rotating boot. Use
a new boot band if the boot band needs to be loosened to reposition the boot.
10. Install circlip and dust cover to housing.
NOTE:
Do not reuse circlip and dust cover.
Wheel Side
1.
Insert the Genuine NISSAN Grease or equivalent, into the joint
sub-assembly serration hole until the grease begins to ooze
from the ball groove and serration hole. Refer to
OMMENDED FLUIDS AND LUBRICANTS"
. After inserting the
grease, use a shop cloth to wipe off the grease that has oozed
out.
2.
Wrap the serrated part of the shaft with tape. Install the boot
band and boot onto the shaft. Do not damage the boot.
NOTE:
Discard the old boot band and boot and use a new one for
assembly.
3.
Remove the protective tape wound around the serrated part of
the shaft.
Boot installation length “L ”
: 163.9 - 164.3 mm
(6.45 - 6.47 in)
SDIA2493E
SFA395
SDIA1127E
SFA800
FAX-12
DRIVE SHAFT
2007 Pathfinder
4.
Attach the circlip to the shaft. The circlip must fit securely into
the shaft groove. Attach the nut to the joint sub-assembly.
Use a soft hammer to press-fit the circlip.
NOTE:
Discard the old circlip and use a new one for assembly.
5.
Insert the specified quantity of Genuine NISSAN Grease or
equivalent, into the joint sub-assembly and the large end of the
boot. Refer to
MA-11, "RECOMMENDED FLUIDS AND LUBRI-
6.
Install the boot securely into the grooves (indicated by the *
marks) as shown.
CAUTION:
If there is grease on the boot mounting surfaces (indicated
by the * marks) of the shaft and joint sub-assembly, the
boot may come off. Remove all grease from the drive shaft
surfaces.
7.
Check that the boot installation length “L” is the specified length.
Insert a flat-tip screwdriver or similar tool into the large side of
the boot. Bleed the air from the boot to prevent boot deforma-
tion.
CAUTION:
●
The boot may break if the boot installation length is less than the specified length.
●
Do not contact inside surface of boot with the tip of the screwdriver.
8.
Secure large and small ends of the boot using new boot bands
using a boot band crimping tool as shown.
NOTE:
Do not reuse boot bands.
●
Secure boot band so that dimension "M" meets specification
as shown.
9.
After installing the housing to the shaft, rotate the boot to check
that it is positioned correctly. If the boot is not positioned cor-
rectly, remove the old boot bands then reposition the boot and
secure the boot with new boot bands.
Grease capacity
: 115
−
135 g (4.01
−
4.76 oz)
RAC0049D
Boot installation length “L”
: 135.1 mm (5.32 in)
Tool number
: KV40107300 (
—
)
SDIA2493E
RAC1133D
Dimension "M"
: 1.0 – 4.0 mm (0.039 – 0.157 in)
DSF0047D
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-13
C
E
F
G
H
I
J
K
L
M
A
B
FAX
2007 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Wheel Bearing
EDS003AF
Drive Shaft
EDS003AG
Boot Bands
EDS003LI
Unit: mm (in)
Axial end play limit
0.05 mm (0.002 in) or less
Drive shaft joint type
Final drive side
Rzeppa
Wheel side
Rzeppa
Grease
Quality
Genuine NISSAN Grease or equivalent
Capacity
Final drive side
120 - 140 g (4.23 - 4.94 oz)
Wheel side
115 - 135 g (4.01 - 4.76 oz)
Boot installed length "L"
Final drive side
163.9 - 164.3 mm (6.45 - 6.47 in)
Wheel side
135.1 mm (5.32 in)
SDIA2493E
Dimension "M"
1.0 - 4.0 (0.039 - 0.157)
DSF0047D
FAX-14
SERVICE DATA AND SPECIFICATIONS (SDS)
2007 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст