Nissan Pathfinder (2007 year). Instruction — part 249
EXHAUST SYSTEM
EX-3
C
D
E
F
G
H
I
J
K
L
M
A
EX
2007 Pathfinder
EXHAUST SYSTEM
PFP:20100
Checking Exhaust System
EBS00QUJ
Check exhaust pipes, muffler and mounting for improper attachment, leaks, cracks, damage or deterioration.
●
If anything is found, repair or replace damaged parts.
Removal and Installation
EBS00QUK
Exhaust System
CAUTION:
●
Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat
resistance, corrosion resistance, and shape.
●
Perform the operation with the exhaust system fully cooled. The system will be hot just after the
engine stops.
●
Be careful not to cut your hand on the heat insulator edge.
SMA211A
WBIA0729E
1.
Tailpipe hanger bracket
2.
Tailpipe
3.
Gasket
4.
Main muffler
5.
Right front exhaust tube
6.
Ring gasket
7.
Heated oxygen sensor 2 (bank 2)
8.
Heated oxygen sensor 2 (bank 1)
9.
Left front exhaust tube
10. Center exhaust tube
11. Muffler hanger bracket front
12. Muffler hanger bracket rear
←
Front
EX-4
EXHAUST SYSTEM
2007 Pathfinder
REMOVAL
Remove exhaust system components using power tool.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
●
Always replace exhaust gaskets with new ones when reassembling.
●
Before installing a new heated oxygen sensor, clean and lube the exhaust tube threads using tool.
●
Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; install a new one.
●
Do not over-torque the heated oxygen sensor. Doing so may damage the heated oxygen sensor,
resulting in the MIL coming on.
●
If any mounting insulator is badly deformed, repair or replace it. If deposits such as mud pile up on
the mounting insulators, clean and inspect them.
●
Temporarily tighten the mounting nuts on the exhaust manifold side and the mounting bolts on the
vehicle side. Check each part for interference with other components, and then tighten the nuts
and bolts to specification.
INSPECTION AFTER INSTALLATION
●
With the engine running, check exhaust tube joints for gas leakage and unusual noises.
●
Check to ensure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
Tool number
A
: —
(J-43897-18)
B
: —
(J-43897-12)
FAX-1
FRONT AXLE
D DRIVELINE/AXLE
CONTENTS
C
E
F
G
H
I
J
K
L
M
SECTION
FAX
A
B
FAX
2007 Pathfinder
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Precautions . . . . . . . . . . . . . . . .. 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 3
NOISE, VIBRATION, AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 4
NVH Troubleshooting Chart . . . . . . . . . . 4
WHEEL HUB . . . . . . . . . . . . . . . .. 5
On-Vehicle Inspection and Service . . . . . . .. 5
WHEEL BEARING INSPECTION . . . . . . . 5
Removal and Installation . . . . . . . . . . .. 5
DRIVE SHAFT . . . . . . . . . . . . . . . . 7
Removal and Installation . . . . . . . . . . .. 7
Disassembly and Assembly . . . . . . . . . .. 8
FAX-2
PRECAUTIONS
2007 Pathfinder
PRECAUTIONS
PFP:00001
Precautions
EDS003A7
Observe the following precautions when disassembling and servicing the wheel hub and drive shafts.
●
Perform work in a location which is as dust-free as possible.
●
Before disassembling and servicing, clean the outside of parts.
●
Prevention of the entry of foreign objects must be taken into account during disassembly of the compo-
nent parts.
●
Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean
cover must be placed over parts.
●
Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adher-
ing to parts.
●
Disassembled parts (except for rubber parts) should be cleaned with a suitable solvent which shall be
removed by blowing with air or wiping with paper shop cloths.
PREPARATION
FAX-3
C
E
F
G
H
I
J
K
L
M
A
B
FAX
2007 Pathfinder
PREPARATION
PFP:00002
Special Service Tools
EDS003A8
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
EDS003A9
Tool number
(Kent-Moore No.)
Tool name
Description
ST29020001
(J-24319-01)
Gear arm puller
Removing ball joint for steering knuckle
a: 34 mm (1.34 in)
b: 6.5 mm (0.256 in)
c: 61.5 mm (2.421 in)
KV38105500
(
—
)
Protector
Installing drive shaft
a: 32 mm (1.26 in) dia
KV40107300
(
—
)
Boot band crimping tool
Installing boot bands
NT694
ZZA0835D
ZZA1229D
Tool name
Description
Power tools
Removing bolts and nuts
PBIC0190E
FAX-4
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
2007 Pathfinder
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
PFP:00003
NVH Troubleshooting Chart
EDS003AA
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
Possible cause and SUSPECTED PARTS
E
xce
ssi
ve j
o
in
t
an
gl
e
J
o
in
t sl
id
in
g
re
si
s
ta
n
ce
Im
b
a
la
n
c
e
Im
pr
ope
r i
n
st
al
la
ti
o
n
, l
oos
ene
ss
P
a
rt
s i
n
te
rf
er
enc
e
W
h
ee
l be
ar
in
g d
a
m
a
g
e
P
R
O
P
E
LLE
R SH
AFT
FR
ON
T F
INA
L DR
IV
E
SU
SP
EN
SI
O
N
TI
R
E
S
RO
AD
W
H
E
E
L
BR
AK
ES
ST
EE
RI
N
G
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
Shudder
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
WHEEL HUB
FAX-5
C
E
F
G
H
I
J
K
L
M
A
B
FAX
2007 Pathfinder
WHEEL HUB
PFP:43202
On-Vehicle Inspection and Service
EDS003AB
Make sure the mounting conditions (looseness, backlash) of each component and component status (wear,
damage) are normal.
WHEEL BEARING INSPECTION
●
Move wheel hub in the axial direction by hand. Make sure there
is no looseness of wheel bearing.
●
Rotate wheel hub and make sure there is no unusual noise or
other irregular conditions. If there are any irregular conditions,
replace wheel hub and bearing assembly.
Removal and Installation
EDS003AC
REMOVAL
1.
Remove wheel and tire using power tool.
2.
Without disassembling the hydraulic lines, remove caliper torque member bolts using power tool. Then
reposition brake caliper aside with wire. Refer to
BR-25, "Removal and Installation of Brake Caliper and
CAUTION:
Do not press brake pedal while brake caliper is removed.
Axial end play limit
: 0.05 mm (0.002 in) or less
SMA571A
1.
Disc rotor
2.
Wheel hub and bearing assembly
3.
Wheel stud
4.
Splash guard
5.
Steering knuckle
6.
Wheel sensor bracket
WDIA0228E
FAX-6
WHEEL HUB
2007 Pathfinder
3.
Put alignment mark on disc rotor and wheel hub and bearing
assembly, then remove disc rotor.
4.
Remove cotter pin, then remove lock nut from drive shaft using power tool. Refer to
5.
Remove drive shaft from wheel hub and bearing assembly. Refer to
FAX-7, "Removal and Installation"
6.
Remove wheel sensor from wheel hub and bearing assembly. Refer to
BRC-59, "Removal and Installa-
●
Inspect the wheel sensor O-ring, replace the wheel sensor assembly if damaged.
●
Clean the wheel sensor hole and mounting surface with a suitable brake cleaner and clean lint-free
shop rag. Be careful that dirt and debris do not enter the axle bearing area.
●
Apply a coat of suitable grease to the wheel sensor O-ring and mounting hole.
CAUTION:
Do not pull on the wheel sensor harness.
7.
Remove wheel hub and bearing assembly bolts using power tool.
8.
Remove splash guard and wheel hub and bearing assembly from steering knuckle.
●
Carefully remove wheel sensor and harness through hole in splash guard.
INSPECTION AFTER REMOVAL
Check for deformity, cracks and damage on each part and replace if necessary.
INSTALLATION
Installation is in the reverse order of removal.
●
Use new bolts when installing the wheel hub and bearing assembly.
●
When installing disc rotor on wheel hub and bearing assembly,
position the disc rotor according to alignment mark.
(When not using the alignment mark, refer to
and Installation of Brake Caliper and Disc Rotor"
.)
●
When installing wheel and tire, refer to
WDIA0044E
WDIA0044E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст