Nissan Pathfinder (2007 year). Instruction — part 230
LUGGAGE FLOOR TRIM
EI-33
C
D
E
F
G
H
J
K
L
M
A
B
EI
2007 Pathfinder
LUGGAGE FLOOR TRIM
PFP:84999
Components
EIS007U8
Luggage Trim - Side
LIIA1783E
EI-34
LUGGAGE FLOOR TRIM
2007 Pathfinder
Luggage Trim - Floor
1.
Metal clip
2.
Garnish
3.
Luggage side upper finisher RH
4.
Luggage side lower finisher RH
5.
Cup holder and tray
6.
Access cover
7.
Luggage side lower finisher LH
8.
Cup holder
9.
Storage bin
10. Access cover
11.
Side cargo net
12. Luggage side upper finisher LH
13. Coat hook
LIIA1784E
1.
Floor storage bin
2.
Flipper panel
3.
Storage tray
4.
Luggage floor board latch
5.
Luggage floor board
6.
Tailgate kick plate
7.
Cargo net
LUGGAGE FLOOR TRIM
EI-35
C
D
E
F
G
H
J
K
L
M
A
B
EI
2007 Pathfinder
Removal and Installation
EIS007U9
REMOVAL
1.
Remove the 2nd and 3rd row seat belts. Refer to
.
2.
Remove the third row seat belt buckles. Refer to
3.
Remove the third row seat assembly. Refer to
4.
Remove the rear door kick plates. refer to
5.
Remove the tailgate kick plate.
6.
Disconnect the door open/close link. Refer to
.
7.
Remove the cargo net hooks.
8.
Remove the LH and RH luggage side lower finishers.
●
Disconnect the power point on the RH side.
9.
Remove the LH and RH coat hooks.
10. Remove the LH and RH luggage side upper finishers.
11. Remove the cargo net hooks LH/RH.
12. Remove the luggage floor board.
13. Remove the flipper panel.
14. Remove the storage tray.
15. Remove the floor storage bin.
INSTALLATION
Installation is in the reverse order of removal.
EI-36
BACK DOOR TRIM
2007 Pathfinder
BACK DOOR TRIM
PFP:90900
Removal and Installation
EIS007UA
REMOVAL
1.
Open back door glass.
2.
Disconnect the gas spring LH and RH from back door (through window garnish).
3.
Open the back door, release the clips and remove back door window garnish.
4.
Remove the screw and back door handle.
5.
Release the clips and remove back door finisher assembly.
INSTALLATION
Installation is in the reverse order of removal.
1.
Back door window garnish
2.
Back door finisher
3.
Back door handle bracket
4.
Back door handle
5.
First aid kit strap
6.
First aid kit
⇐
Vehicle front
WIIA0725E
EM-1
ENGINE MECHANICAL
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION
EM
A
EM
2007 Pathfinder
PRECAUTIONS . . . . . . . . . . . . . . .. 4
REMOVAL OF LIQUID GASKET SEALING . . .. 5
LIQUID GASKET APPLICATION PROCEDURE
PREPARATION . . . . . . . . . . . . . . ... 7
Special Service Tools . . . . . . . . . . . ... 7
Commercial Service Tools . . . . . . . . . . 9
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . ...11
ENGINE ROOM COVER . . . . . . . . . . .. 13
Removal and Installation . . . . . . . . . . 13
REMOVAL . . . . . . . . . . . . . . ... 13
INSTALLATION . . . . . . . . . . . . ... 13
DRIVE BELTS . . . . . . . . . . . . . . ... 14
DRIVE BELT . . . . . . . . . . . . . ... 14
INSTALLATION . . . . . . . . . . . . ... 15
Drive Belt Auto Tensioner and Idler Pulley . . . . 15
REMOVAL . . . . . . . . . . . . . . ... 15
INSTALLATION . . . . . . . . . . . . ... 15
AIR CLEANER AND AIR DUCT . . . . . . . ... 16
Removal and Installation . . . . . . . . . . 16
REMOVAL . . . . . . . . . . . . . . ... 16
INSPECTION AFTER REMOVAL . . . . . ... 16
INSTALLATION . . . . . . . . . . . . ... 16
Changing Air Cleaner Filter . . . . . . . . . 16
REMOVAL . . . . . . . . . . . . . . ... 16
INSTALLATION . . . . . . . . . . . . ... 16
INTAKE MANIFOLD COLLECTOR . . . . . . .. 17
Removal and Installation . . . . . . . . . . 17
REMOVAL . . . . . . . . . . . . . . ... 18
INSTALLATION . . . . . . . . . . . . ... 19
INTAKE MANIFOLD . . . . . . . . . . . . . 20
Removal and Installation . . . . . . . . . . 20
EXHAUST MANIFOLD AND THREE WAY CATA-
LYST . . . . . . . . . . . . . . . . . . .. 22
Removal and Installation . . . . . . . . . . 22
OIL PAN AND OIL STRAINER . . . . . . . . . 27
Removal and Installation . . . . . . . . . . 27
IGNITION COIL . . . . . . . . . . . . . . . 32
EM-2
2007 Pathfinder
SPARK PLUG . . . . . . . . . . . . . . ... 33
Changing Spark Plugs . . . . . . . . . . . 33
FUEL INJECTOR AND FUEL TUBE . . . . . . 35
Removal and Installation . . . . . . . . . . 35
ROCKER COVER . . . . . . . . . . . . . . 41
Removal and Installation . . . . . . . . . . 41
FRONT TIMING CHAIN CASE . . . . . . . . . 46
Removal and Installation . . . . . . . . . . 46
TIMING CHAIN . . . . . . . . . . . . . . .. 55
Removal and Installation . . . . . . . . . . 55
CAMSHAFT . . . . . . . . . . . . . . . ... 75
Removal and Installation . . . . . . . . . . 75
Valve Clearance . . . . . . . . . . . . . .. 84
INSPECTION . . . . . . . . . . . . . ... 84
ADJUSTMENT . . . . . . . . . . . . . 87
OIL SEAL . . . . . . . . . . . . . . . . .. 89
Removal and Installation of Valve Oil Seal . . . . 89
REMOVAL . . . . . . . . . . . . . . ... 89
INSTALLATION . . . . . . . . . . . . . 89
Removal and Installation of Front Oil Seal . . . . 90
REMOVAL . . . . . . . . . . . . . . ... 90
INSTALLATION . . . . . . . . . . . . . 90
Removal and Installation of Rear Oil Seal . . . .. 91
REMOVAL . . . . . . . . . . . . . . ... 91
INSTALLATION . . . . . . . . . . . . . 91
CYLINDER HEAD . . . . . . . . . . . . . . 92
On-Vehicle Service . . . . . . . . . . . . . 92
CHECKING COMPRESSION PRESSURE . . . 92
Removal and Installation . . . . . . . . . . 93
Disassembly and Assembly . . . . . . . . . 97
DISASSEMBLY . . . . . . . . . . . . ... 97
ASSEMBLY . . . . . . . . . . . . . . ..98
Inspection After Disassembly . . . . . . . . ..99
ENGINE ASSEMBLY . . . . . . . . . . . ...104
Removal and Installation . . . . . . . . . ...104
CYLINDER BLOCK . . . . . . . . . . . . .107
Disassembly and Assembly . . . . . . . . ..107
DISASSEMBLY . . . . . . . . . . . . ..108
ASSEMBLY . . . . . . . . . . . . . . 112
How to Select Piston and Bearing . . . . . . 118
Inspection After Disassembly . . . . . . . . 123
SERVICE DATA AND SPECIFICATIONS (SDS) . 133
EM-3
C
D
E
F
G
H
I
J
K
L
M
EM
A
2007 Pathfinder
EM-4
PRECAUTIONS
2007 Pathfinder
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EBS00T2W
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Drain Engine Coolant
EBS00QB8
Drain engine coolant when engine is cooled.
Precautions for Disconnecting Fuel Piping
EBS00QB9
●
Before starting work, make sure no fire or spark producing items are in the work area.
●
Release fuel pressure before disconnecting and disassembly.
●
After disconnecting pipes, plug openings to stop fuel leakage.
Precautions for Removal and Disassembly
EBS00QBA
●
When instructed to use SST, use specified tools. Always be careful to work safely, avoid forceful or unin-
structed operations.
●
Exercise maximum care to avoid damage to mating or sliding surfaces.
●
Cover openings of engine system with tape or equivalent, if necessary, to seal out foreign materials.
●
Mark and arrange disassembly parts in an organized way for easy troubleshooting and re-assembly.
●
When loosening nuts and bolts, as a basic rule, start with the one furthest outside, then the one diagonally
opposite, and so on. If the order of loosening is specified, do exactly as specified. Power tools may be
used in the step.
Precautions for Inspection, Repair and Replacement
EBS00QBB
Before repairing or replacing, thoroughly inspect parts. Inspect new replacement parts in the same way, and
replace if necessary.
Precautions for Assembly and Installation
EBS00QBC
●
Use torque wrench to tighten bolts or nuts to specification.
●
When tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with the
ones in center, then ones on inside and outside diagonally in this order. If the order of tightening is speci-
fied, do exactly as specified.
●
Replace with new gasket, packing, oil seal or O-ring.
●
Thoroughly wash, clean, and air-blow each part. Carefully check engine oil or engine coolant passages for
any restriction and blockage.
●
Avoid damaging sliding or mating surfaces. Completely remove foreign materials such as cloth lint or dust.
Before assembly, oil sliding surfaces well.
●
Release air within route when refilling after draining engine coolant.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст