Nissan Primera P11. Instruction — part 29
YAT255
TROUBLE DIAGNOSES FOR NON-DETECTABLE ITEMS
Wiring Diagram — AT — NONDTC (Cont’d)
AT-113
Control Cable Adjustment
NCAT0111
Move selector lever from the “P” position to the “L” position. You
should be able to feel the detents in each position. If the detents
cannot be felt or if the pointer indicating the position is improperly
aligned, the control cable needs adjustment.
1.
Place selector lever in “P” position.
2.
Loosen control cable lock nut and place instruction shaft in “P”
position.
CAUTION:
Turn wheels more than 1/4 rotations and apply the park lock.
3.
Tighten control cable lock nut.
: 12 - 14 N
⋅
m (1.2 - 1.5 kg-m, 9 - 10 ft-lb)
4.
Move selector lever from “P” to “L” position again. Make sure
that selector lever moves smoothly.
5.
Apply grease to contacting areas of selector lever and control
cable. Install any part removed.
Park/Neutral Position (PNP) Switch Adjustment
NCAT0112
1.
Remove control cable end from instruction shaft.
2.
Set instruction shaft in “N” position.
3.
Loosen PNP switch fixing bolts.
4.
Use a 4 mm (0.157 in) pin for this adjustment.
a.
Insert the pin straight into the instruction shaft adjustment hole.
b.
Rotate PNP switch until the pin can also be inserted straight
into hole in PNP switch.
5.
Tighten PNP switch fixing bolts.
: 4.9 - 6.8 N
⋅
m (0.5 - 0.7 kg-m, 44 - 60 in-lb)
6.
Remove pin from adjustment hole after adjusting PNP switch.
7.
Reinstall any part removed.
8.
Adjust control cable. Refer to “Control Cable Adjustment”.
9.
Check continuity of PNP switch. Refer to AT-53.
Differential Side Oil Seal Replacement
NCAT0113
1.
Remove drive shaft assemblies. Refer to FA section (“Drive
Shaft”, “FRONT AXLE”).
2.
Remove oil seals.
SAT658J
Control cable
Lock nut
Instruction shaft
SAT659J
Pin
PNP switch
Instruction shaft
(N range)
SAT660J
Oil seal
ON-VEHICLE SERVICE
Control Cable Adjustment
AT-114
3.
Install oil seals.
I
Apply CVT fluid to oil seal surface before installing.
I
Install oil seals so that dimensions “A” and “B” are within
specifications.
Unit: mm (in)
A
B
5.5 - 6.5 (0.217 - 0.256)
−0.5 to 0.5 (−0.020 to 0.020)
4.
Reinstall any part removed.
SAT661J
Left side
Right side
ON-VEHICLE SERVICE
Differential Side Oil Seal Replacement (Cont’d)
AT-115
Removal
NCAT0115
CAUTION:
Before separating transaxle from engine, remove the crank-
shaft position sensor (OBD) from transaxle. Be careful not to
damage sensor.
1.
Remove battery and bracket.
2.
Remove air duct between throttle body and air cleaner.
3.
Disconnect control valve harness connector, PNP switch har-
ness connector, secondary speed sensor harness connector,
dropping resistor harness connector, primary speed sensor
harness connector and body earth harness connector.
4.
Remove crankshaft position sensor (OBD) from transaxle.
5.
Drain CVT fluid from transaxle.
6.
Disconnect control cable from transaxle.
7.
Remove exhaust front tube. Refer to FE section (“EXHAUST
SYSTEM”).
8.
Remove drive shafts. Refer to FA section (“Drive Shaft”,
“FRONT AXLE”).
9.
Disconnect oil cooler hoses.
10. Remove starter motor from transaxle.
Tighten bolts to specified torque.
: 41 - 52 N
⋅
m (4.2 - 5.3 kg-m, 30 - 38 ft-lb)
11. Support transaxle with a jack.
12. Remove center member.
I
Tighten center member fixing bolts to specified torque, Refer
to EM section (“ENGINE REMOVAL”).
13. Remove rear plate cover.
14. Remove torque converter bolts.
Rotate crankshaft to gain access to securing bolts.
15. Support engine with a jack.
16. Remove transaxle mount bolt. Refer to EM section (“ENGINE
REMOVAL”).
17. Remove oil cooler tube (outlet side).
18. Remove transaxle.
Inspection
NCAT0236
I
When connecting torque converter to transaxle, measure dis-
tance “A” to be certain that they are correctly assembled.
Distance “A”:
15.9 mm (0.626 in) or more
SAT664J
SAT665J
REMOVAL AND INSTALLATION
Removal
AT-116
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст