Nissan Primera P11. Instruction — part 55
Body Front End
●
When removing or installing hood, place a cloth or other padding on the front fender panels and cowl
top. This prevents vehicle body from being scratched.
●
Bumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
●
Hood adjustment: Adjust at hinge portion.
●
Hood lock adjustment: After adjusting, check hood lock control operation. Apply a coat of grease to hood
locks engaging mechanism.
●
Hood opener: Do not attempt to bend cable forcibly. Doing so increases effort required to unlock hood.
REMOVAL — Front bumper assembly
p
1
Remove clips
C205
securing bumper fascia to engine undercover.
p
2
Remove screws and clips
C205
securing left and right sides of front fender protector.
p
3
Remove screws securing radiator core support to bumper fascia.
p
4
Remove screws securing left and right front fenders to bumper fascia.
p
5
Remove clips
CS101
securing retainer to bumper fascia.
p
6
Extract bumper fascia assembly.
p
7
Remove screws securing fog lamps. Then remove fog lamps.
YBT001
10.8 - 14.6 N·m
(1.1 - 1.5 kg-m,
8.0 - 10.8 ft-lb)
BODY END
BT-5
NBT033
SEC. 261
⋅
620
⋅
623
⋅
650
⋅
656
Hood lock adjustment
●
Adjust hood so that hood primary lock
meshes at a position 1 to 1.5 mm (0.039 to
0.059 in) lower than fender.
●
After hood lock adjustment, adjust bumper
rubber.
●
When securing hood lock, ensure it does not
tilt. Striker must be positioned at the center of
hood primary lock.
●
After adjustment, ensure that hood primary and sec-
ondary lock operate properly.
More than 5.0 mm (0.197 in)
Hood
Secondary latch
Bumper rubber adjustment
●
Adjust so that hood is aligned
with fender. At that time deflection
is approx. 2 mm (0.08 in).
[Bumper rubber free height is
approx. 13 mm (0.51 in).]
Hood adjustment
20.6 - 26.5
(2.1 - 2.7,
15 - 20)
Bumper fascia assembly
★
: Bumper assembly mounting bolts, screw & clips
: N·m (kg-m, ft-lb)
Fog lamp
CS101
★
★
C205
C205
★
★
★
.
Hood lock secondary latch hooking length
BODY END
Body Front End (Cont’d)
BT-6
Body Rear End and Opener
4-DOOR SEDAN
●
When removing or installing trunk lid, place a cloth or other padding on rear fender panels. This pre-
vents vehicle body from being scratched.
●
Bumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
●
Trunk lid adjustment: Adjust at hinge-trunk lid portion for proper trunk lid fit.
●
Trunk lid lock system adjustment: Adjust striker so that it is in the center of the lock. After adjustment,
check trunk lid lock operation.
WARNING:
●
Be careful not to scratch trunk lid stay when installing trunk lid.
A scratched stay may cause gas leakage.
●
The contents of the trunk lid stay are under pressure. Do not take apart puncture, apply heat or
allow fire near it.
●
Opener cable: Do not attempt to bend cable using excessive force.
●
After installation, make sure that trunk lid and fuel filler lid open smoothly.
NBT034
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
Upper
Spring holder
Lower
Opener handle
Opener cable
Lock nut
Fuel filler lid opener & control
Trunk lid striker
.
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
: N·m (kg-m, ft-lb)
20.6 - 26.5
(2.1 - 2.7,
15 - 20)
: N·m (kg-m, in-lb)
Cloth
Actuator
.
Trunk lid lock
key cylinder
.
Trunk lid lock
.
5.1 - 6.37
(0.52 - 0.65, 45.1 - 56.4)
BODY END
BT-7
REMOVAL — Rear bumper assembly
p
1
Remove license plate lamp.
p
2
Remove clips
C203
securing left and right chipping protector.
p
3
Remove screws securing bumper fascia to left and right rear fenders.
p
4
Remove clips
CS101
securing bumper fascia to real panel.
p
5
Remove clips
C205
securing bumper fascia to rear panel upper.
p
6
Extract bumper fascia assembly.
YBT062
BODY END
Body Rear End and Opener (Cont’d)
BT-8
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст