Nissan Primera P11. Instruction — part 302
WARNING:
●
The xenon headlamp has a high-tension current generating area. Be extremely careful when
removing and installing. Be certain to disconnect the battery negative cable prior to removing or
installing.
●
When the xenon headlamp is lit, do not touch the harness (covered with red or amber insulation),
bulb itself or the bulb socket with your bare hands.
●
Never service a xenon headlamp with wet hands.
●
When checking body side harness with a circuit tester, be certain to disconnect the harness
connector from the xenon headlamp.
●
When the xenon headlamp is lit, the xenon bulb must be installed in the headlamp housing.
(Never turn on xenon headlamp, if the bulb is out of the headlamp housing.)
CAUTION:
Make sure to install the bulb securely; if the xenon bulb is improperly installed in its socket, high-
tension current leaks occur. This may lead to a melted bulb and/or bulb socket.
Trouble Diagnoses
Symptom
Possible cause
Repair order
LH or RH xenon headlamp
(low beam) blinks, lacks
brightness or does not illu-
minate.
1. 15A fuse
1. Check 20A fuse [No.
30
(gasoline engine),
43
(diesel engine) : LH, No.
38
(gasoline engine),
39
(diesel engine), : RH, located in fuse and fusible
link box].
2. Relay
2. Check Headlamp relay.
3. Power supply circuit to headlamp
low beam
3. Verify battery positive voltage is present at terminal
쑗
3
of headlamp harness with lighting switch in
“2nd” and “Low” positions. (Before inspecting head-
lamp terminal, disconnect headlamp connector with
lighting switch in “OFF” position.)
4. Xenon bulb
4. Replace the xenon bulb with the other side bulb or
new one. (If headlamps illuminate correctly, replace
the bulb.)
5. HID control unit and booster
5. Replace the HID control unit and booster as a head-
lamp assembly.
LH or RH [both headlamp
high and xenon (low) beam]
do not illuminate.
1. 15A fuse
1. Check 15A fuse [No.
30
(Gasoline engine), No.
43
(diesel engine), : LH, No.
38
(gasoline engine),
No.
39
(diesel engine) located in fuse and fusible
link box].
2. Ground circuit
2. Check continuity between headlamp harness termi-
nal
쑗
2
and body ground. (Before inspecting head-
lamp terminal, disconnect headlamp connector with
lighting switch in “OFF” position.)
LH or RH headlamp high
beam does not illuminate.
1. Bulb
2. Power supply circuit to headlamp
high beam
1. Check bulb.
2. Verify battery positive voltage is present at terminal
쑗
1
of headlamp harness with lighting switch in
“2nd” and “HIGH” position. (Before inspecting head-
lamp terminal, disconnect headlamp connector with
lighting switch in “OFF” position.)
HID: High Intensity Discharge
HEADLAMP (without Daytime Light System) — Xenon Type —
EL-75
Bulb Replacement
CAUTION:
●
After replacing a new xenon bulb, be sure to make aim-
ing adjustments.
●
Hold only the plastic base when handling the bulb. Never
touch the glass envelope.
●
Do not leave headlamp reflector without bulb for a long
period of time. Dust, moisture, smoke, etc. entering
headlamp body may affect the performance of the head-
lamp. Remove headlamp bulb from the headlamp reflec-
tor just before a replacement bulb is installed.
1. Disconnect negative battery cable.
2. Remove side combination lamp and radiator grille.
3. Disconnect headlamp connector.
4. Remove headlamp assembly.
WARNING:
Never service a xenon headlamp with wet hands.
XENON BULB (LOW BEAM)
1. Remove headlamp seal cover.
2. Turn bulb socket counterclockwise with keep pushing, then
remove it.
3. Release retaining pin.
4. Remove the xenon bulb.
5. Install in the reverse order of removal.
CAUTION:
●
When disposing of the xenon bulb, do not break it;
always dispose of it as is.
●
Make sure to install the bulb securely; if the xenon bulb
is improperly installed in its socket, high-tension current
leaks occur. This may lead to a melted bulb and/or bulb
socket.
NEL765
.
Bulb Socket
NEL551
Retaining pin
HEADLAMP (without Daytime Light System) — Xenon Type —
EL-76
HIGH BEAM
1. Pull off headlamp seal cover.
2. Disconnect bulb connector.
3. Release retaining pin.
4. Remove the bulb.
5. Install in the reverse order of removal.
NEL564
.
Seal cover
Retaining pin
HEADLAMP (without Daytime Light System) — Xenon Type —
Bulb Replacement (Cont’d)
EL-77
Schematic
CONVENTIONAL
TYPE
YEL273C
BATTERY
FUSE
COMBINATION SWITCH
(LIGHTING SWITCH)
HEADLAMP
RELAY LH
COMBINATION
METER
(HI BEAM INDI-
CATOR)
LOW
HIGH
HEADLAMP LH
LOW
HIGH
HEADLAMP RH
HEADLAMP
RELAY RH
IGNITION SWITCH
ON or START
IGNITION SWITCH
START
DAYTIME LIGHT CONTROL UNIT
To tail lamp
ALTERNATOR
OFF
1ST
2ND
HEADLAMP
—
Daytime
Light
System
—
EL-78
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст