Nissan Primera P11. Instruction — part 505
Checking Body Corrosion
Visually check body panels for corrosion, paint damage (scratches, chipping, rubbing, etc.) or damage to
the anti-corrosion materials. In particular, check the following locations.
Hemmed panels
Hood front end, door lower end, trunk lid rear end, etc.
Panel joint
Side sill of rear fender and center pillar, rear wheel housing of rear fender, around strut tower in engine
compartment, etc.
Panel edge
Trunk lid opening, sunroof opening, fender wheel-arch flange, fuel filler lid flange, around holes in panel, etc.
Parts contact
Waist moulding, windshield moulding, bumper, etc.
Protectors
Damage or condition of mudguard, fender protector, chipping protector, etc.
Anti-corrosion materials
Damage or separation of anti-corrosion materials under the body.
Drain holes
Condition of drain holes at door and side sill.
When repairing corroded areas, refer to the Corrosion Repair Instruction.
CHASSIS AND BODY MAINTENANCE
MA-55
Engine Maintenance
INSPECTION AND ADJUSTMENT
Drive belt deflection and tension
Deflection adjustment
Unit: mm (in)
Tension adjustment*
Unit: N (kg, lb)
Used belt
New belt
Used belt
New belt
Limit
After
adjustment
Limit
After
adjustment
Alternator
Without aircondi-
tioner compressor
10.2
(0.402)
6.5 - 7.0
(0.256 - 0.276)
5.5 - 6.1
(0.217 - 0.240)
292
(29.8, 65.6)
652 - 740
(66.5 - 75.5,
146.6 - 166.4)
789 - 877
(80.5 - 89.7,
177.4 - 197.6)
With airconditioner
compressor
8.1
(0.319)
5.3 - 5.7
(0.209 - 0.224)
4.5 - 5.0
(0.177 - 0.197)
Power steering
oil pump
10.8
(0.425)
6.6 - 7.5
(0.260 - 0.295)
6.0 - 6.6
(0.236 - 0.260)
196
(20.0, 44.1)
495 - 583
(50.5 - 59.5,
111.3 - 131.1)
603 - 691
(61.5 - 70.5,
135.6 - 155.3)
Applied pushing force
98 N (10 kg, 22 lb)
—
*: If belt tension gauge cannot be installed at check points shown, check drive belt tension at a different location on the belt.
Oil capacity (Refill capacity)
Unit:
(Imp pts)
With oil filter change
2.9 (5 - 1/8)
Without oil filter change
2.7 (4 - 3/4)
Coolant capacity
Unit:
(Imp pts)
With reservoir tank
6.1 (10 - 3/4)
Reservoir tank
0.8 (1 - 3/8)
Spark plug
Make
CHAMPION
NGK
Standard type
RC10YCC4
RC10YC4
BKR5E-11
Hot type
RC12YCC4
RC12YC4
BKR4E-11
Cold type
RC7YCC4
RC7YC4
BKR6E-11
Plug gap
mm (in)
1.0 - 1.1 (0.039 - 0.043)
SERVICE DATA AND SPECIFICATIONS (SDS)
QG
MA-56
Engine Maintenance
INSPECTION AND ADJUSTMENT
Drive belt deflection and tension
Deflection adjustment
Unit: mm (in)
Tension adjustment*
Unit: N (kg, lb)
Used belt
New belt
Used belt
New belt
Limit
After adjust-
ment
Limit
After adjust-
ment
Alternator
12 - 13
(0.47 - 0.51)
8 - 9
(0.31 - 0.35)
7 - 8
(0.28 - 0.31)
264
(26.9, 59.3)
493 - 583
(50.3 - 59.5,
110.8 - 131.1)
11720 70J00
11720 70J05
603 - 691
(61.5 - 70.5,
135.6 - 155.3)
652 - 740
(66.5 - 75.5,
146.6 - 166.4)
Air condi-
tioner com-
pressor
9 (0.35)
5.5 - 6.5
(0.217 -
0.256)
4.5 - 5.5
(0.177 -
0.217)
304
(31.0, 68.3)
534 - 623
(54.5 - 63.5,
120.0 - 140.1)
11920 9F500
11920 9F505
652 - 740
(66.5 - 75.5,
146.6 - 166.4)
838 - 926
(85.5 - 94.5,
188 - 208)
Power steer-
ing oil pump
12
(0.47)
8 - 9
(0.31 - 0.35)
7 - 8
(0.28 - 0.31)
264
(26.9, 59.3)
493 - 583
(50.3 - 59.5,
110.8 - 131.1)
603 - 691
(61.5 - 70.5,
135.6 - 155.3)
603 - 691
(61.5 - 70.5,
135.6 - 155.3)
Applied push-
ing force
98 N (10 kg, 22 lb)
—
*: If belt tension gauge cannot be installed at check points shown, check drive belt tension at a different location on the belt.
Oil capacity (Refill capacity)
Unit:
(Imp pts)
With oil filter change
3.7 (6 - 1/2)
Without oil filter change
3.5 (6 - 1/8)
Coolant capacity (Refill capacity)
Unit:
(Imp pts)
Engine
SR20DE
With reservoir tank
M/T
6.6 (11 - 5/8)
CVT
6.8 (12)
Reservoir tank
0.8 (1 - 3/8)
Spark plug
Make
NGK
Type
Standard
BKR6EY-11
Hot
—
Cold
—
Plug gap
mm (in)
1.0 - 1.1 (0.039 - 0.043)
Ignition lead
Unit: k
Ω
/m
Ignition lead
Resistance [at 25°C (77°F)]
No. 1 cylinder
Approx 3.8
No. 2 cylinder
Approx 3.5
No. 3 cylinder
Approx 2.7
No. 4 cylinder
Approx 2.4
For U.K. (Made by Bougicord) 4.48 - 6.72 k
Ω
(1.365 - 2.048
k
Ω
/ft) [at 25°C (77°F)]
SERVICE DATA AND SPECIFICATIONS (SDS)
SR20DE
MA-57
Engine Maintenance
INSPECTION AND ADJUSTMENT
Drive belt deflection
Deflection adjustment
Unit: mm (in)
Used belt
New belt
Limit
After adjustment
Alternator
17 (0.67)
10.5 - 12.5
(0.413 - 0.492)
8.5 - 10.5
(0.335 - 0.413)
Air conditioner compressor
17 (0.67)
11.5 - 13.5
(0.453 - 0.531)
9.5 - 11.5
(0.374 - 0.453)
Power steering oil pump
8 (0.31)
5 - 7
(0.20 - 0.28)
4 - 6
(0.16 - 0.24)
Applied pushing force
98 N (10 kg, 22 lb)
Coolant capacity (Refill capacity)
Unit:
(Imp pts)
With reservoir tank
6.4 (11 - 1/4)
Reservoir tank
0.8 (1 - 3/8)
Engine oil capacity (Refill capacity)
Unit:
(Imp pts)
With oil filter
5.0 (8 - 3/4)
Without oil filter
4.5 (7 - 7/8)
Injection nozzle
Unit: kPa (bar, kg/cm
2
, psi)
Injection pressure
12,749 (127.5, 130, 1,849)
SERVICE DATA AND SPECIFICATIONS (SDS)
CD20T
MA-58
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст