Nissan Frontier D22. Instruction — part 933
TF-38
REPAIR FOR COMPONENT PARTS
AIR BREATHER
Removal and Installation
Remove air breather by pulling straight out and install at specified
angle, as shown.
Shift Control Components
EDS0011U
INSPECTION
Check contact surface and sliding surface for wear, scratches, pro-
jections or other faulty conditions, as shown.
L & H Shift Rod & Fork
Assemble as shown.
●
* Retaining pin is the same size as the one for 2-4 shift rod.
2-4 Shift Rod & Fork
Assemble as shown in illustration.
●
* Retaining pins are the same size.
SMT799A
SMT360A
SMT319A
SMT320A
REPAIR FOR COMPONENT PARTS
TF-39
C
E
F
G
H
I
J
K
L
M
A
B
TF
●
Pay special attention to the direction of fork guide collar.
SMT321A
TF-40
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
General Specifications
EDS0011V
Inspection and Adjustment
EDS0011W
CLEARANCE BETWEEN FRONT DRIVE SPROCKET AND 2-4 COUPLING SLEEVE
Unit: mm (in)
GEAR END PLAY
Unit: mm (in)
CLEARANCE BETWEEN BAULK RING AND CLUTCH GEAR
Unit: mm (in)
Available Shim
EDS0011X
COUNTER GEAR REAR BEARING
*: Always check with the Parts Department for the latest parts information.
Available Snap Ring
EDS0011Y
MAINSHAFT FRONT BEARING
*: Always check with the Parts Department for the latest parts information.
MAIN GEAR BEARING
Transfer model
TX10A
Gear ratio
High
1.000
Low
2.020
Number of teeth
Main gear
29
Low gear
37
Counter gear
High
38
Low
24
Front drive sprocket
41
Front drive shaft
41
Fluid capacity
(US qt, Imp qt)
2.2 (2-3/8, 2)
Allowable clearance "C"
0.2 - 0.54 (0.0079 - 0.0213)
Front drive sprocket
0.2 - 0.35 (0.0079 - 0.0138)
Low gear
0.2 - 0.35 (0.0079 - 0.0138)
Counter gear
0 - 0.2 (0 - 0.0079)
Standard
Wear limit
1.0 - 1.5 (0.039 - 0.059)
0.5 (0.020)
Allowable clearance
0 - 0.2 mm (0 - 0.0079 in)
Thickness mm (in)
Part No.*
0.1 (0.004)
0.2 (0.008)
0.3 (0.012)
0.4 (0.016)
0.5 (0.020)
0.6 (0.024)
33112-C6900
33112-C6901
33112-C6902
33112-C6903
33112-33G00
33112-33G01
Allowable clearance
0 - 0.15 mm (0 - 0.0059 in)
Thickness mm (in)
Part No.*
3.10 (0.1220)
3.19 (0.1256)
3.28 (0.1291)
33138-73P10
33138-73P11
33138-73P12
Allowable clearance
0 - 0.15 mm (0 - 0.0059 in)
SERVICE DATA AND SPECIFICATIONS (SDS)
TF-41
C
E
F
G
H
I
J
K
L
M
A
B
TF
*: Always check with the Parts Department for the latest parts information.
MAINSHAFT REAR BEARING
*: Always check with the Parts Department for the latest parts information.
Thickness mm (in)
Part No.*
2.60 (0.1024)
2.69 (0.1059)
2.78 (0.1094)
33114-73P00
33114-73P01
33114-73P02
Allowable clearance
0 - 0.15 mm (0 - 0.0059 in)
Thickness mm (in)
Part No.*
1.80 (0.0709)
1.89 (0.0744)
1.98 (0.0780)
2.07 (0.0815)
2.16 (0.0850)
33138-73P20
33138-73P21
33138-73P22
33138-73P23
33138-73P24
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст