Nissan Frontier D22. Instruction — part 777
LT-26
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram — TURN —
EKS006VS
WKWA0374E
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-27
C
D
E
F
G
H
I
J
L
M
A
B
LT
WKWA0375E
LT-28
TURN SIGNAL AND HAZARD WARNING LAMPS
Trouble Diagnoses
EKS006VT
Symptom
Possible cause
Repair order
Turn signal and hazard warning
lamps do not operate.
1. 7.5A fuse
2. 10A fuse
3. Hazard switch
4. Combination flasher unit
5. Open in combination flasher unit
circuit
1. Check 7.5A fuse [No. 2, located in fuse block (J/B)].
Turn ignition switch ON and verify battery positive volt-
age is present at terminal 2 of hazard switch.
2. Check 10A fuse [No. 17, located in fuse block (J/B)].
Verify battery positive voltage is present at terminal 3 of
hazard switch.
3. Check hazard switch.
4. Refer to combination flasher unit check.
5. Check wiring to combination flasher unit for open circuit.
Turn signal lamps do not operate
but hazard warning lamps operate.
1. 7.5A fuse
2. Hazard switch
3. Turn signal switch
4. Open in turn signal switch circuit
1. Check 7.5A fuse [No. 2, located in fuse block (J/B)].
Turn ignition switch ON and verify battery positive volt-
age is present at terminal 2 of hazard switch.
2. Check hazard switch.
3. Check turn signal switch.
4. Check G wire between combination flasher unit and
turn signal switch for open circuit.
Check the harness between turn signal switch and front
combination lamp for open circuit.
Hazard warning lamps do not oper-
ate but turn signal lamps operate.
1. 10A fuse
2. Hazard switch
3. Open in hazard switch circuit
1. Check 10A fuse [No. 17, located in fuse block (J/B)].
Verify battery positive voltage is present at terminal 3 of
hazard switch.
2. Check hazard switch.
3. Check G wire between combination flasher unit and
hazard switch for open circuit.
Front turn signal lamp LH or RH
does not operate.
1. Bulb
2. Front turn signal lamp ground cir-
cuit
1. Check bulb.
2. Check grounds E12 and E54 and continuity between
front turn signal lamp and grounds E12 and E54.
Rear turn signal lamp LH does not
operate.
1. Bulb
2. Rear combination lamp LH
ground circuit
1. Check bulb.
2. Check grounds M14 and M68 and continuity between
rear combination lamp LH and grounds M14 and M68.
Rear turn signal lamp RH does not
operate.
1. Bulb
2. Rear turn signal lamp RH ground
circuit
1. Check bulb.
2. Check grounds M14 and M68 and continuity between
rear combination lamp RH and grounds M14 and M68.
LH and RH turn indicators do not
operate.
1. Ground circuit
1. Check grounds M14 and M68 and continuity between
combination meter terminal 13 and grounds M14 and
M68.
LH or RH turn indicator does not
operate.
1. Bulb
2. Combination meter
3. Turn indicator circuit
1. Check bulb in cluster lid A.
2. Check continuity between combination meter terminal
12, 14 and 13.
3. Check the wire between hazard switch and combination
meter.
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-29
C
D
E
F
G
H
I
J
L
M
A
B
LT
Electrical Components Inspection
EKS006VU
COMBINATION FLASHER UNIT CHECK
●
Before checking, ensure that bulbs meet specifications.
●
Connect a battery and test lamp to the combination flasher unit,
as shown. Combination flasher unit is properly functioning if it
blinks when power is supplied to the circuit.
SEL122E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст