Nissan Frontier D22. Instruction — part 874
RFD-4
[C200]
PREPARATION
KV38100600
(J25267)
Side bearing spacer drift
Installing side bearing spacer
a: 8 mm (0.31 in)
b: R42.5 mm (1.673 in)
ST30611000
(J25742-1)
Drift
Installing pinion rear bearing outer race
ST30621000
(J25742-5)
Drift
Installing pinion rear bearing outer race
a: 79 mm (3.11 in) dia.
b: 59 mm (2.32 in) dia.
ST30613000
(J25742-3)
Drift
Installing pinion front bearing outer race
a: 72 mm (2.83 in) dia.
b: 48 mm (1.89 in) dia.
KV38100500
(J25273)
Gear carrier front oil seal drift
Installing front oil seal
a: 85 mm (3.35 in) dia.
b: 60 mm (2.36 in) dia.
(J34309)
Differential shim selector
Adjusting bearing pre-load and gear height
(J25269-4)
Side bearing discs
(2 Req'd)
Selecting pinion height adjusting washer
Tool number
(Kent-Moore No.)
Tool name
Description
NT528
NT090
NT073
NT073
NT115
NT134
NT136
PREPARATION
RFD-5
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RFD
(J8129)
Spring gauge
Measuring carrier turning torque
KV381051S0
(
—
)
Rear axle shaft dummy
1 KV38105110
(
—
)
Torque wrench side
2 KV38105120
(
—
)
Vise side
Checking differential torque on limited slip dif-
ferential
KV10112100
(BT8653-A)
Angle wrench
Tightening side bearing cap bolts
Tool number
(Kent-Moore No.)
Tool name
Description
NT127
NT142
S-NT014
RFD-6
[C200]
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
PFP:00003
NVH Troubleshooting Chart
EDS0012Q
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
,
—
,
,
Possible cause and SUSPECTED PARTS
R
o
ugh gea
r t
o
ot
h
Im
pr
o
per
g
ear
co
nt
act
T
oot
h sur
fac
e w
o
rn
In
c
o
rr
e
c
t b
a
c
k
la
s
h
C
o
m
pani
on f
lan
ge exce
ssi
ve r
unou
t
Im
pr
o
per
g
ear
oi
l
PROPEL
LER SHAFT
AXL
E AND
SUSPENSION
TIRES
ROAD W
H
EE
L
DRIVESHAFT
BRAKE
S
ST
EERI
N
G
Symptom
DIFFERENTIAL
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
FRONT OIL SEAL
RFD-7
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RFD
FRONT OIL SEAL
PFP:38189
Removal and Installation
EDS0012R
1.
Remove propeller shaft. Refer to
PR-8, "Removal and Installation"
2.
Loosen drive pinion nut while holding companion flange using
Tool.
3.
Remove companion flange using a suitable tool.
4.
Remove ABS sensor and rear wheel sensor rotor.
5.
Remove front oil seal.
6.
Apply multi-purpose grease to cavity at sealing lips of oil seal.
Press front oil seal into carrier using Tool.
7.
Install ABS sensor and rear wheel sensor rotor.
8.
Install companion flange.
Tool number
: KV38108300 (J-44195)
APD032
SPD737
WPD013
Tool number
: KV38100500 (J25273)
ABS sensor
bolts
: 18 - 24 N·m (1.8 - 2.4 kg-m,
13 - 17 lb-ft)
WPD014
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст