Nissan Frontier D22. Instruction — part 310
DTC P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-343
[KA24DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
8.
CHECK INPUT SIGNAL CIRCUIT
1.
Disconnect ECM harness connector.
2.
Check harness continuity between ECM terminal 62 and EVAP control system pressure sensor terminal
2.
Refer to Wiring Diagram.
3.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 9.
9.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors C1, M67
●
Harness connectors M59, F27
●
Harness for open or short between EVAP control system pressure sensor and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
10.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR HOSE
1.
Turn ignition switch OFF.
2.
Check disconnection or improper connection of hose connected to EVAP control system pressure sensor.
OK or NG
OK
>> GO TO 11.
NG
>> Repair it.
Continuity should exist.
EC-344
[KA24DE]
DTC P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
11.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
1.
Remove EVAP control system pressure sensor with its harness
connector connected.
2.
Remove hose from EVAP control system pressure sensor.
3.
Use pump to apply vacuum and pressure to EVAP control system pressure sensor as shown in figure.
CAUTION:
●
Always calibrate the vacuum pump gauge when using it.
●
Do not apply below
−93.3 kPa (−700 mmHg, −27.56 inHg) or over 101.3 kPa (760 mmHg, 29.56
inHg) of pressure.
4.
Check output voltage between ECM terminal 62 and engine
ground.
CAUTION:
Discard any EVAP control system pressure sensor which
has been dropped from a height of more than 0.5 m (19.7 in)
onto a hard surface such as a concrete floor; use a new
one.
OK or NG
OK
>> GO TO 12.
NG
>> Replace EVAP control system pressure sensor.
12.
CHECK INTERMITTENT INCIDENT
EC-120, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END.
SEF341V
Applied vacuum kPa (mmHg, inHg)
Voltage [V]
Not applied
1.8 - 4.8
-26.7 (-200, -7.87)
2.1 to 2.5V lower than above value
SEF198V
DTC P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-345
[KA24DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
PFP:25085
Component Description
UBS00D7Y
The EVAP control system pressure sensor detects pressure in the
purge line. The sensor output voltage to the ECM increases as pres-
sure increases. The EVAP control system pressure sensor is not
used to control the engine system. It is used only for on board diag-
nosis.
CONSULT-II Reference Value in Data Monitor Mode
UBS00D7Z
Specification data are reference values.
On Board Diagnosis Logic
UBS00D80
SEF340V
PBIB1207E
MONITOR ITEM
CONDITION
SPECIFICATION
EVAP SYS PRES
●
Ignition switch: ON
1.8 - 4.8V
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0453
EVAP control system
pressure sensor high
input
An excessively high voltage from
the sensor is sent to ECM.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
EVAP control system pressure sensor
●
Rubber hose to EVAP control system pressure is
clogged, vent, kinked, disconnected or improper
connection.
●
EVAP canister vent control valve
●
EVAP canister purge volume control solenoid valve
●
EVAP canister
●
Water separator
EC-346
[KA24DE]
DTC P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
DTC Confirmation Procedure
UBS00D81
NOTE:
If “DTC Confirmation Procedure” has been previously conducted, always turn ignition switch OFF and wait at
least 5 seconds before conducting the next test.
TESTING CONDITION:
●
Always perform test at a temperature above 5
°C (41°F).
●
Before performing the following procedure, confirm battery voltage is more than 11V at idle.
WITH CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 5 seconds.
3.
Turn ignition switch ON.
4.
Select “DATA MONITOR” mode with CONSULT-II.
5.
Make sure that “FUEL T/TMP SE” is more than 0
°C (32°F).
6.
Start engine and wait at least 20 seconds.
7.
If 1st trip DTC is detected, go to
EC-348, "Diagnostic Procedure"
.
WITH GST
1.
Start engine and warm it up to normal operating temperature.
2.
Check that voltage between ECM terminal 60 (Fuel tank temper-
ature sensor signal) and ground is less than 4.2V.
3.
Turn ignition switch OFF and wait at least 5 seconds.
4.
Start engine and wait at least 20 seconds.
5.
Select “MODE 7” with GST.
6.
If 1st trip DTC is detected, go to
EC-348, "Diagnostic Procedure"
.
SEF194Y
SEF196V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст