Nissan Frontier D22. Instruction — part 859
PR-10
PROPELLER SHAFT ASSEMBLY
2.
Put match marks on the flange and shaft.
3.
Remove locking nut with Tool.
4.
Remove companion flange with puller.
5.
Remove center bearing with Tool and press.
JOURNAL
1.
Put match marks on shaft and flange or yoke.
2.
Remove snap ring.
SPD110
Tool number
: KV38108300 (J-44195)
SPD475A
Tool number
: ST30031000 (J22912-01)
SPD113
SPD128
APD011
PROPELLER SHAFT ASSEMBLY
PR-11
C
E
F
G
H
I
J
K
L
M
A
B
PR
3.
Remove pushed out journal bearing by lightly tapping yoke with
a hammer, taking care not to damage journal and yoke hole.
4.
Remove bearing at opposite side in above operation.
Put marks on disassembled parts so that they can be rein-
stalled in their original positions from which they were
removed.
Assembly
EDS00127
CENTER BEARING
1.
When installing center bearing, position the “F” mark on center
bearing toward front of vehicle.
Apply a coat of multi-purpose lithium grease containing
molybdenum disulfide to the end face of the center bearing
and both sides of the washer.
2.
Stake the nut. Always use a new one.
3.
Align match marks when assembling tubes.
SPD732
SPD131
SPD114
SPD117
PR-12
PROPELLER SHAFT ASSEMBLY
JOURNAL
1.
Assemble journal bearing. Apply recommended multi-purpose
grease on bearing inner surface.
When assembling, be careful that needle bearing does not
fall down.
2.
Install new snap rings.
3.
Adjust thrust clearance between bearing and snap ring to zero
by tapping yoke.
4.
Check to see that journal moves smoothly and check for axial
play.
WPD019
APD012
SPD732
Axial play
: 0.02 mm (0.0008 in) or less
SPD874
SERVICE DATA AND SPECIFICATIONS (SDS)
PR-13
C
E
F
G
H
I
J
K
L
M
A
B
PR
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
General Specifications
EDS00128
2WD KA24DE MODELS
2WD VG33E AND VG33ER MODELS
4WD MODELS
Propeller shaft model
M/T
A/T
3S1310
Number of joints
3
Coupling method with transmission
Sleeve type
Type of journal bearings
Solid type (disassembly type)
Shaft length (Spider to spider)
mm (in)
1st tube
644.7 (25.38)
549.6 (21.64)
2nd tube
970.3 (38.20)
970.3 (38.20)
Shaft diameter
mm (in)
1st tube
63.5 (2.50)
63.5 (2.50)
2nd tube
63.5 (2.50)
63.5 (2.50)
Grade
XE, SE
SC
Transmission
M/T
A/T
M/T
A/T
Model
K/C, C/C
C/C Long
bed
SK/C, C/C
C/ C Long
bed
K/C, C/C
C/C Long
bed
K/C, C/C
C/C Long
bed
Propeller shaft model
3S1310
3S80B-
2BJ
3S1310
3S80B-
2BJ
3S1310
Number of joints
3
3
Coupling method with
transmission
Sleeve type
Type of journal bearings
Solid type (disassembly type)
Solid type
(disassem-
bly type
without
Birfield
joint)
Solid type
(disassem-
bly type)
Solid type
(disassem-
bly type
without
Birfield
joint)
Solid type
(disassem-
bly type)
Distance between yokes
mm (in)
80 (3.15)
Shaft
length
(Spider to
spider)
mm (in)
1st tube
661
(26.02)
1043
(41.06)
566
(22.28)
948
(37.32)
681
(26.81)
1043
(41.06)
586
(23.07)
948
(37.32)
2nd tube
982.3 (38.67)
984.3
(38.75)
984.2
(38.75)
980
(38.58)
982.3
(38.67)
980
(38.58)
984.2
(38.75)
Shaft outer
diameter
mm (in)
1st tube
63.5 (2.50)
76.2 (2.99)
63.5 (2.50)
76.2 (2.99)
75 (2.95)
76.2 (2.99)
75 (2.95)
76.2 (2.99)
2nd tube
63.5 (2.50)
65 (2.56)
63.5 (2.50)
65 (2.56)
63.5 (2.50)
Grade
XE, SE
SC
Location
Front
Rear
Front
Rear
Model
All
K/C, C/C
C/C Long bed
All
K/C, C/C
C/C Long
bed
Propeller shaft model
2F1310
2S1310
3S1310
2F1310
2S1310
3S1310
Number of joints
2
2
3
2
2
3
Coupling method with transmission
Flange type
Sleeve type
Flange type
Sleeve type
Type of journal bearings
Solid type (disassembly type)
Distance between yokes mm (in)
71 (2.80)
80 (3.15)
71 (2.80)
80 (3.15)
Shaft length (Spider to
spider) mm
(in)
1st tube
522 (20.55)
1247 (49.09)
637 (25.07)
522 (20.55)
1247 (49.09)
637 (25.07)
2nd tube
—
—
989 (38.93)
—
—
989 (38.93)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст