Nissan Rogue. Instruction — part 414

DLN-100

< REMOVAL AND INSTALLATION >

[REAR PROPELLER SHAFT: C-CVJ-C]

REAR PROPELLER SHAFT

REMOVAL AND INSTALLATION

REAR PROPELLER SHAFT

Exploded View

INFOID:0000000011278392

Removal and Installation

INFOID:0000000011278393

REMOVAL

1. Shift the transaxle to the neutral position, and then release the parking brake.
2. Remove muffler assembly. Refer to

EX-5, "Removal and Installation"

.

3. Put matching marks onto propeller shaft flange yoke and final

drive and transfer companion flanges.

CAUTION:

For matching marks, use paint. Do not damage propeller

shaft flange yoke and transfer companion flange.

Center bearing mounting bracket
(upper)

Clip

Propeller shaft assembly

Center bearing mounting bracket
(lower)

: Vehicle front

: N·m (kg-m, ft-lb)

: Always replace after every disassembly.

JSDIA5323GB

JSDIA0194ZZ

REAR PROPELLER SHAFT

DLN-101

< REMOVAL AND INSTALLATION >

[REAR PROPELLER SHAFT: C-CVJ-C]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

4. Loosen nuts of center bearing brackets (upper/lower).

CAUTION:

Tighten nuts temporarily.

5. Remove propeller shaft assembly bolts and nuts.
6. Remove center bearing bracket nuts.
7. Remove propeller shaft assembly.

CAUTION:

If constant velocity joint was bent during propeller shaft

assembly removal, installation, or transportation, its boot

may be damaged. Wrap boot interference area to metal part with shop cloth or rubber to protect

boot from breakage.

8. Remove clips and center bearing bracket (upper/lower).

INSTALLATION

Installation is in the reverse order of removal.

• When removing propeller shaft from final drive assembly (electric controlled coupling), replace stud bolts of

electric controlled coupling.

• Install center bearing bracket (upper) (1) with its arrow mark (A)

facing forward.

• Adjust position of center bearing bracket (upper), center bearing

bracket (lower) (2) sliding back and forth to prevent play in thrust

direction of center bearing insulator (3). Install center bearing

bracket (upper/lower) to vehicle.

• Align matching marks to install propeller shaft assembly to final

drive and transfer companion flanges.

• Perform inspection after installation. Refer to

DLN-102, "Inspec-

tion"

.

• After tightening the bolts and nuts to the specified torque, make

sure that the bolts (3) on the flange side is tightened as shown in

the figure.

• If propeller shaft assembly or final drive assembly (electric controlled coupling) has been replaced, connect

them as follows:

: Front

JSDIA0195ZZ

JSDIA0127ZZ

(1)

: Transfer assembly

(2)

: Propeller shaft assembly

JSDIA0196ZZ

DLN-102

< REMOVAL AND INSTALLATION >

[REAR PROPELLER SHAFT: C-CVJ-C]

REAR PROPELLER SHAFT

- Install propeller shaft (1) while aligning its matching marks (A) on

propeller shaft with matching mark (B) on electric controlled cou-

pling (2) and join them as close as possible.

Inspection

INFOID:0000000011278394

INSPECTION AFTER REMOVAL

Appearance

Check propeller shaft tube surface for dents or cracks. If malfunction is detected, replace propeller shaft

assembly.

Propeller Shaft Runout

Check propeller shaft runout at measuring points with a dial indica-

tor. If runout exceeds specifications, replace propeller shaft assem-

bly.

• Propeller shaft runout measuring point (Point “ ”).

Journal Axial Play

As shown in the figure, while fixing yoke on one side, check axial

play of joint. If it is outside the standard, replace propeller shaft

assembly.

CAUTION:

Never disassemble joints.

Center Bearing

Check center bearing for noise and damage. If malfunction is detected, replace propeller shaft assembly.

CAUTION:

JSDIA5332ZZ

Propeller shaft runout : Refer to

DLN-104, "Propeller

Shaft Runout"

.

JSDIA0193ZZ

: Front side

Dimension
A

: 541.5 mm (21.32 in)

B

: 488.7 mm (19.24 in)

JPDID0001ZZ

Journal axial play : Refer to

DLN-104, "Journal Axial

Play"

.

PDA0005D

REAR PROPELLER SHAFT

DLN-103

< REMOVAL AND INSTALLATION >

[REAR PROPELLER SHAFT: C-CVJ-C]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

Never disassemble center bearing.

INSPECTION AFTER INSTALLATION

After assembly, perform a driving test to check propeller shaft vibration. If vibration occurred, separate propel-

ler shaft from final drive. Reinstall propeller shaft by changing the phase between electric controlled coupling

stud bolt and propeller shaft by the one bolt hole at a time. Then perform driving test and check propeller shaft

vibration again at each point.