Nissan Rogue. Instruction — part 415
DLN-104
< SERVICE DATA AND SPECIFICATIONS (SDS)
[REAR PROPELLER SHAFT: C-CVJ-C]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000011278395
Propeller Shaft Runout
INFOID:0000000011278396
Unit: mm (in)
Journal Axial Play
INFOID:0000000011278397
Unit: mm (in)
Applied model
AWD
QR25DE
CVT
Propeller shaft model
C-CVJ-C
Number of joints
3
Joint type
1st joint
Universal (Shell type)
2nd joint
CVJ type
3rd joint
Universal (Shell type)
Coupling method
Transfer side
Flange type
Rear final drive side
Flange type
Shaft length
1st (Spider to CVJ joint center)
1196 mm (47.09 in)
2nd (CVJ joint center to spider)
983 mm (38.70 in)
Shaft outer diameter
1st
63.5 mm (2.500 in)
2nd
70.0 mm (2.756 in)
Item
Standard
Propeller shaft runout
0.6 (0.024) or less
Item
Standard
Journal axial play
0 (0)
PRECAUTIONS
DLN-105
< PRECAUTION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011278398
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Service Notice or Precautions for Rear Final Drive
INFOID:0000000011278399
• Check for the correct installation status prior to removal or disassembly. If matching marks are required, be
certain they never interfere with the function of the parts when applied.
• Overhaul should be done in a clean work area, it is preferable to work in dustproof area.
• Before disassembly, using steam or white gasoline, completely remove sand and mud from the exterior of
the unit, preventing them from entering into the unit during disassembly or assembly.
• Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace them
with a new ones if necessary.
• Gaskets, seals and O-rings should be replaced any time when the unit is disassembled.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If tight-
ening sequence is specified, observe it.
• Clean and flush the parts sufficiently and blow-dry them.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mounting surface; then remove any moisture, oil,
and foreign materials from the application and mounting surfaces.
• Always use shop paper for cleaning the inside of components.
• Never use cotton gloves or shop rags to prevent entering of lint.
• During assembly, observe the specified tightening torque, and apply new gear oil, petroleum jelly, or multi-
purpose grease as specified for each vehicle, if necessary.
DLN-106
< PREPARATION >
[REAR FINAL DRIVE: R145]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000011278400
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
KV38100200
(J-26233)
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
• Installing drive pinion oil seal
• Installing side oil seal
ST27861000
(
—
)
Drift
a: 62 mm (2.44 in) dia.
b: 52 mm (2.05 in) dia.
Installing drive pinion oil seal
ST35271000
(J-26091)
Drift
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.
Installing drive pinion oil seal
KV40100610
(J-26089)
Drift
a: 63 mm (2.48 in) dia.
b: 54.3 mm (2.138 in) dia.
• Removing and installing gear carrier and
rear cover (2 pieces are used)
• Installing pinion front bearing inner race
ST33052000
(
—
)
Adaptor
a: 22 mm (0.87 in) dia.
b: 28 mm (1.10 in) dia.
Removing side bearing inner race
KV40105020
(
—
)
Drift
a: 39.7 mm (1.563 in) dia.
b: 35 mm (1.38 in) dia.
c: 15 mm (0.59 in)
Installing side bearing inner race
ZZA1143D
ZZA0832D
ZZA0814D
ZZA1000D
ZZA1023D
ZZA1133D
PREPARATION
DLN-107
< PREPARATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
KV38109500
(
—
)
Drive pinion socket
• Removing and installing drive pinion lock
nut
• Measuring preload torque
KV38109400
(
—
)
Pinion nut wrench
Removing and installing drive pinion lock nut
ST33200000
(J-26082)
Drift
a: 60 mm (2.36 in) dia.
b: 44.5 mm (1.752 in) dia.
Installing pinion rear bearing outer race
ST33230000
(J-25805-01)
Drift
a: 51 mm (2.01 in) dia.
b: 41 mm (1.61 in) dia.
c: 28.5 mm (1.122 in) dia.
Installing pinion front bearing outer race
ST23860000
(
—
)
Drift
a: 38 mm (1.50 in) dia.
b: 33 mm (1.30 in) dia.
• Installing pinion rear bearing inner race
• Installing pinion front bearing inner race
ST38220000
(
—
)
Press stand
a: 63 mm (2.48 in) dia.
b: 65 mm (2.56 in)
Installing pinion front bearing inner race
Tool number
(TechMate No.)
Tool name
Description
ZZA1205D
ZZA1206D
ZZA1002D
ZZA1046D
ZZA0534D
ZZA1058D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст