Nissan Rogue. Instruction — part 375
DLK-342
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM, all door lock actuator connectors.
2. Check continuity between BCM harness connector and rear door lock actuator LH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock actuator LH. Refer to
DLK-388, "DOOR LOCK : Removal and Installation"
.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
REAR RH
REAR RH : Component Function Check
INFOID:0000000011279115
1.
CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR LOCK” in “Active Test”.
3. Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-342, "REAR RH : Diagnosis Procedure"
REAR RH : Diagnosis Procedure
INFOID:0000000011279116
Regarding Wiring Diagram information, refer to
.
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear door lock actuator RH connector.
BCM
Rear door lock actuator LH
Continuity
Connector
Terminal
Connector
Terminal
B23
148
D206
2
Yes
149
1
BCM
Ground
Continuity
Connector
Terminal
B23
148
No
149
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
B23
148
Ground
Door lock and unlock switch
Unlock
Battery voltage
149
Lock
2015 Rogue NAM
DOOR LOCK ACTUATOR
DLK-343
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Check voltage between rear door lock actuator RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock actuator RH. Refer to
DLK-388, "DOOR LOCK : Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM, all door lock actuator connectors.
2. Check continuity between BCM harness connector and rear door lock actuator RH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock actuator RH. Refer to
DLK-388, "DOOR LOCK : Removal and Installation"
.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
(+)
(–)
Condition
Voltage
(Approx.)
Rear door lock actuator RH
Connector
Terminal
D306
5
Ground
Door lock and unlock switch
Unlock
Battery voltage
6
Lock
BCM
Rear door lock actuator RH
Continuity
Connector
Terminal
Connector
Terminal
B23
148
D306
6
Yes
149
5
BCM
Ground
Continuity
Connector
Terminal
B23
148
No
149
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
B23
148
Ground
Door lock and unlock switch
Unlock
Battery voltage
149
Lock
2015 Rogue NAM
DLK-344
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB BATTERY AND FUNCTION
KEYFOB BATTERY AND FUNCTION
Description
INFOID:0000000011279117
The following functions are available when having and carrying the keyfob:
• Door lock/unlock
• Panic mode (horn and head-lamp operation)
Remote control entry function and panic alarm function are available when operating the remote buttons.
Component Function Check
INFOID:0000000011279118
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech
II User Guide for additional information.
• Check keyfob relative signal strength
• Confirm vehicle antenna signal strength
1.
CHECK FUNCTION
With CONSULT
Check remote keyless entry receiver “KEYLESS LOCK”, “KEYLESS UNLOCK”, and “KEYLESS PANIC” in
“Data Monitor”.
Is the inspection result normal?
YES
>> Keyfob is OK.
NO
>> Refer to
DLK-344, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000011279119
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II
User Guide for additional information.
• Check keyfob relative signal strength
• Confirm vehicle antenna signal strength
1.
CHECK KEYFOB FUNCTION
Check keyfob function using Signal Tech II Tool [– (J-50190)] or
Remote Keyless Entry Tester [– (J-43241)] (shown).
Does the test pass?
YES
>> Keyfob is OK.
NO
>> GO TO 2.
2.
CHECK KEYFOB BATTERY
Monitor item
Condition
KEYLESS LOCK
Checks whether value changes from “Off” to “On” when operating keyfob lock button.
KEYLESS UNLOCK
Checks whether value changes from “Off” to “On” when operating keyfob unlock button.
KEYLESS PANIC
Checks whether value changes from “Off” to “On” when operating keyfob panic button.
ALKIA2300ZZ
2015 Rogue NAM
KEYFOB BATTERY AND FUNCTION
DLK-345
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Check by connecting a resistance (approximately 300
Ω) so that the
current value becomes about 10 mA.
Is the measurement value within specification?
YES
>> Keyfob battery is OK.
NO
>> GO TO 3.
3.
REPLACE KEYFOB BATTERY
1. Replace the keyfob battery with a new one (CR2032 or equivalent).
CAUTION:
• When replacing battery, keep dirt, grease, and other foreign materials off the electrode contact
area.
• Make sure that the + side faces the bottom of the case.
2. Align the tips of the upper and lower parts, and then push them together until it is securely closed.
3. After replacing the battery, check that all keyfob functions work properly.
Is the inspection result normal?
YES
>> Keyfob is OK.
NO
>> Check BCM.
Standard
: Approx. 2.5 - 3.0V
OCC0607D
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст