Nissan Rogue. Instruction — part 376
DLK-346
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HORN FUNCTION
HORN FUNCTION
Component Function Check
INFOID:0000000011279120
1.
CHECK FUNCTION 1
1. Perform “SIREN” in “Active Test” of “THEFT ALM” of “BCM” using CONSULT.
2. Check the horn operation.
Is the operation normal?
YES
>> Inspection End.
NO
>> Go to
.
Component Inspection
INFOID:0000000011279121
1.
CHECK ANTI-THEFT HORN RELAY
1. Turn ignition switch OFF.
2. Disconnect anti-theft horn relay.
3. Check voltage between anti-theft horn relay E101 terminal 2 and ground under the following conditions:
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace anti-theft horn relay.
Test item
Description
HORN
ON
Horn
Sounds (for 0.5 sec)
(+)
(
−)
Condition
Voltage (V)
(Approx.)
Anti-theft horn relay
Terminal
2
Ground
12 V direct current supply between terminals 1 and 2
12
No current supply
0
2015 Rogue NAM
WARNING CHIME FUNCTION
DLK-347
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WARNING CHIME FUNCTION
Description
INFOID:0000000011279122
Performs operation method guide and warning with buzzer.
Component Function Check
INFOID:0000000011279123
1.
CHECK FUNCTION
With CONSULT
1. Check the operation with “BUZZER” in the “Active Test”.
2. Touch “IGN KEY WARN ALM”, “SEAT BELT WARN TEST”or “LIGHT WARN ALM”on screen.
Is the inspection result normal?
YES
>> Warning buzzer into combination meter is OK.
NO
>> Refer to
DLK-347, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000011279124
1.
CHECK METER BUZZER CIRCUIT
Operate the hazard lights by turning ON the hazard warning switch.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> Inspection End.
2015 Rogue NAM
DLK-348
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HAZARD FUNCTION
HAZARD FUNCTION
Description
INFOID:0000000011279125
Perform answer-back for each operation with number of blinks.
Component Function Check
INFOID:0000000011279126
1.
CHECK FUNCTION
Check hazard warning lamp “FLASHER” in “Active Test”.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
DLK-348, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000011279127
1.
CHECK HAZARD SWITCH CIRCUIT
Operate the hazard lights by turning ON the hazard warning switch.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace hazard warning switch circuit. Refer to
EXL-125, "Removal and Installation"
.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> Inspection End.
2015 Rogue NAM
THIS PAGE INTENTIONALLY LEFT BLANK
DLK-349
>
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
.
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст