Nissan Rogue. Instruction — part 380
DLK-362
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD
2. Remove hood hinge to hood nuts (A) and hood assembly.
NOTE:
RH side shown; LH similar.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.
• After installation, perform the hood assembly adjustment procedure. Refer to
.
HOOD ASSEMBLY : Adjustment
INFOID:0000000011279137
Check the clearance and the surface height between hood and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dures.
ALKIA3338ZZ
1.
Hood assembly
2.
Front grille
3.
Front combination lamp
4.
Fender
5.
Bumper rubber
6.
Hood hinge
7.
Hood lock
AWKIA2916ZZ
2015 Rogue NAM
HOOD
DLK-363
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit: mm (in)
HEIGHT ADJUSTMENT
1. Loosen the hood lock assembly bolts.
2. Adjust the surface height of hood assembly to front grille and front fender according to the specified val-
ues by rotating hood bumper rubber.
3. Temporarily tighten hood lock assembly bolts.
4. Adjust (A) and (B) as shown to the following value with hood's own weight by dropping it from approxi-
mately 200 mm (7.87 in) height or by pressing hood lightly [approximately 29 N (3.0 kg, 6.5 lb)].
5. After adjustment, tighten hood hinge nuts and bolts to the specified torque.
CAUTION:
• Check hood hinge rotating part for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After adjusting, apply touch-up paint (body color) to the head of hood hinge bolts and nuts.
CLEARANCE ADJUSTMENT
1. Loosen hood hinge nuts and bolts.
2. Loosen the hood lock assembly bolts.
3. Adjust the hood assembly so the clearance measurements are within specifications.
4. Tighten the hood hinge nuts and bolts to specified torque.
5. Tighten the hood lock assembly bolts to specified torque.
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000011279138
REMOVAL
1. Remove hood assembly. Refer to
DLK-361, "HOOD ASSEMBLY : Removal and Installation"
Portion
Section
Item
Measurement
Standard
Parallelism
Hood - Fender
A - A
D
Surface height
0.0
± 1.0 (0.0 ± 0.04)
1.4 (0.06)
E
Clearance
3.5
± 1.5 (0.14 ± 0.04)
1.4 (0.06)
Fender - Front combination lamp
B - B
F
Clearance
9.0
± 2.0 (0.35 ± 0.08)
2.0 (0.08)
Hood - Front combination lamp
C - C
G
Clearance
1.9
± 1.1 (0.07 ± 0.04)
1.5 (0.06)
1.
Secondary striker
2.
Primary striker
3.
Hood assembly
A.
20 mm (0.79 in)
B.
6.8 mm (0.27 in)
AWKIA2925ZZ
2015 Rogue NAM
DLK-364
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD
2. Remove front fender. Refer to
DLK-366, "Removal and Installation"
3. Remove hood hinge bolts, and then remove hood hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.
• After installation, perform hood assembly adjustment procedure. Refer to
2015 Rogue NAM
RADIATOR CORE SUPPORT
DLK-365
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000011279139
Removal and Installation
INFOID:0000000011279140
CAUTION:
When removing radiator core support upper, be careful not to damage the painted surface.
REMOVAL
Radiator Core Upper Support
1. Remove front combination lamp (LH). Refer to
EXL-119, "Removal and Installation"
2. Remove front air duct. Refer to
3. Remove hood lock. Refer to
DLK-260, "HOOD LOCK : Removal and Installation"
4. Remove secondary latch. Refer to
DLK-261, "SECONDARY LATCH : Removal and Installation"
.
5. Remove crash zone sensor. Refer to
SR-22, "Removal and Installation"
.
6. Remove bolts and radiator core upper support.
Radiator Core Lower Support
1. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
2. Support the radiator using a suitable tool.
3. Remove bolts and radiator core lower support.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Tighten bolts to specified torque. Refer to
.
1.
Radiator core upper support
2.
Secondary latch bracket
3.
Radiator core lower support
ALKIA3498ZZ
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст