Nissan Rogue. Instruction — part 381
DLK-366
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT FENDER
FRONT FENDER
Exploded View
INFOID:0000000011279141
Removal and Installation
INFOID:0000000011279142
CAUTION:
Use a shop cloths to protect the body from being damaged during removal and installation.
REMOVAL
1. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
2. Remove front combination lamp. Refer to
EXL-119, "Removal and Installation"
(HALOGEN HEADLAMP)
EXL-266, "Removal and Installation"
. (LED HEADLAMP).
3. Remove center mudguard. Refer to
EXT-43, "Removal and Installation"
.
4. Remove screws (A) and front fender bracket (1).
5. Remove bolts and front fender.
CAUTION:
Use care when removing the front fender. The front fender baffle foam adheres the front fender to
the body side outer. Carefully release the baffle foam or damage to the front fender may occur.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation apply touch up paint (body color) to the head of front fender bolts.
• After installation, adjust the following components as necessary:
- Hood assembly: Refer to
DLK-362, "HOOD ASSEMBLY : Adjustment"
.
- Front door: Refer to
DLK-369, "DOOR ASSEMBLY : Adjustment"
1.
Front fender
AWKIA2926ZZ
ALKIA3354ZZ
2015 Rogue NAM
FRONT FENDER
DLK-367
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Tighten bolts to specification. Refer to
2015 Rogue NAM
DLK-368
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR
FRONT DOOR
Exploded View
INFOID:0000000011279143
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000011279144
CAUTION:
• Use two people when removing or installing the front door due to its heavy weight.
• When removing and installing front door assembly, support front door with a suitable tool.
REMOVAL
1. Disconnect the battery negative and positive terminals and wait at least three minutes with the side air
bag (satellite) sensor.
2. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
3. Remove front door vapor barrier (1).
NOTE:
LH side shown; RH similar.
1.
Front door panel
2.
Grommet
3.
Bumper rubber
4.
Door striker
5.
Door check link
6.
Front door lower hinge
7.
Front door upper hinge
AWKIA2927ZZ
ALKIA3488ZZ
2015 Rogue NAM
FRONT DOOR
DLK-369
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4. Disconnect the harness connectors from the front door.
5. Remove front door harness grommet, then harness from the front door.
6. Remove front door check link bolt (body side).
7. Remove front door hinge nuts (door side) and front door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten nuts/bolts to specified torque. Refer to
• Apply anticorrosive agent where necessary.
• After installation, check front door open/close and lock/unlock operation.
• After installation, perform the front door adjustment procedure. Refer to
DOOR ASSEMBLY : Adjustment
INFOID:0000000011279145
ADJUSTMENT
Check the clearance and surface height between front door and each part by visual inspection and tactile feel.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Front door upper hinge
6.
Front door lower hinge
7.
Door striker
F.
Front door striker bolts
AWKIA2885ZZ
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст