Nissan Rogue. Instruction — part 624
HAZARD SWITCH
EXL-125
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Exploded View
INFOID:0000000011280790
Removal and Installation
INFOID:0000000011280791
REMOVAL
1. Remove center ventilator grille. Refer to
VTL-13, "CENTER VENTILATOR GRILLE : Removal and Instal-
.
2. Release the pawls and remove the hazard switch.
INSTALLATION
Installation is in the reverse order of removal.
1.
Center ventilator grille
2.
Hazard switch
Pawl
AWLIA2315ZZ
EXL-126
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
SIDE TURN SIGNAL LAMP
SIDE TURN SIGNAL LAMP
Removal and Installation
INFOID:0000000011280792
REMOVAL
1. Remove door mirror rear finisher. Refer to
MIR-26, "Removal and Installation"
2. Remove door mirror glass. Refer to
MIR-24, "Removal and Installation"
3. Remove the screws (A) and reposition side turn signal lamp.
4. Disconnect the harness connector from the side turn signal lamp and remove.
INSTALLATION
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000011280793
The side turn signal lamp bulb is not serviced separately. Refer to
EXL-126, "Removal and Installation"
.
AWLIA2319ZZ
REAR COMBINATION LAMP
EXL-127
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP
Exploded View
INFOID:0000000011280794
Removal and Installation
INFOID:0000000011280795
REMOVAL
1. Remove side air spoiler. Refer to
EXT-49, "Removal and Installation"
2. Remove rear combination lamp bolts.
3. Pull rear combination lamp rearward to release from clip and locators.
4. Disconnect the harness connector from the rear combination lamp and remove.
INSTALLATION
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000011280796
WARNING:
Do not touch bulb with bare hand while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP LAMP BULB
1.
Rear combination lamp
A.
Grommet
Clip
AWLIA2488ZZ
EXL-128
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
REAR COMBINATION LAMP
Removal
1. Remove rear combination lamp. Refer to
EXL-127, "Removal and Installation"
2. Rotate stop lamp bulb socket counterclockwise and remove.
3. Remove stop lamp bulb from bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install bulb socket securely for watertightness.
TAIL LAMP BULB
Removal
1. Remove rear combination lamp. Refer to
EXL-127, "Removal and Installation"
2. Rotate tail lamp bulb socket counterclockwise and remove.
3. Remove tail lamp bulb from bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install bulb socket securely for watertightness.
TURN SIGNAL LAMP BULB
Removal
1. Remove rear combination lamp. Refer to
EXL-127, "Removal and Installation"
2. Rotate turn signal lamp bulb socket counterclockwise and remove.
3. Remove turn signal lamp bulb from bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install bulb socket securely for watertightness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст