Nissan Rogue. Instruction — part 578
CAMSHAFT
EM-77
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
c. Apply liquid gasket to the positions shown. Refer to
ommended Chemical Products and Sealants"
d. Install valve timing control cover.
• Tighten the bolts to specification in the numerical order as
shown.
9. Check and adjust valve clearances. Refer to
EM-21, "Camshaft valve clearance"
10. Install camshaft position sensor bracket.
a. Apply liquid gasket to camshaft position sensor bracket as
shown.
CAUTION:
• Use Genuine Silicone RTV Sealant, or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
• After installation be sure to wipe off excessive liquid gas-
ket leaking from part (B).
• Installation should be done within 5 minutes after apply-
ing liquid gasket.
• Do not fill the engine with engine oil for at least 30 minutes after the components are installed to
allow the liquid gasket to cure.
b. Tighten bolts to specification in numerical order shown.
11. Install the camshaft position sensors. Refer to
.
12. Installation of the remaining components is in the reverse order of removal.
Inspection After Installation
INFOID:0000000011279968
Inspection of Camshaft Sprocket (INT) Oil Groove and Camshaft Sprocket (EXH) Oil Groove
Diameter (A)
: 3.4 - 4.4 mm (0.134 - 0.173 in)
AWBIA1362ZZ
ALBIA0839GB
(A) : 2.0 - 3.0 mm (0.079-0.118)
(B) : 10.5 mm (0.413 in)
Camshaft position
sensor bracket bolts
: 10.41 N·m (1.1 kg-m, 8 ft-lb)
ALBIA0907GB
ALBIA0908GB
EM-78
< REMOVAL AND INSTALLATION >
CAMSHAFT
WARNING:
Check when engine is cold so as to prevent burns from any splashing engine oil.
CAUTION:
Perform this inspection only when DTC P0011, P0014, P052A, P052B is detected in self-diagnostic
results of CONSULT and it is directed according to inspection procedure of EC section.
1. Check engine oil level and adjust oil level as necessary. Refer to
.
2. Remove the intake valve timing intermediate lock control solenoid valve, intake valve timing control sole-
noid valve, and exhaust valve timing control solenoid valve. Refer to
EM-79, "Intake Valve Timing Interme-
.
3. Perform the following procedure to prevent the engine from being unintentionally started while checking.
a. Release fuel pressure. Refer to
b. Disconnect injector harness connectors.
4. Crank engine, and then make sure that engine oil comes out of
the valve timing control cover oil holes (A). End cranking after
checking.
WARNING:
Be careful not to touch rotating parts (drive belt, crankshaft
pulley, etc.).
CAUTION:
• Engine oil may squirt from intake valve timing intermedi-
ate lock control solenoid valve, intake valve timing control
solenoid valve, exhaust valve timing control solenoid
valve installation holes during cranking. Use a shop cloth
to prevent engine oil from splashing on worker, engine
components and vehicle.
• Do not allow engine oil to get on rubber components such as drive belts or engine mount insula-
tors. Immediately wipe off any splashed engine oil.
5. If engine oil does not come out from valve timing control cover oil holes (A), diagnose problem in lubrica-
tion circuit such as dirty oil groove between oil strainer and intake valve timing intermediate lock control
solenoid valve, intake valve timing control solenoid valve, or exhaust valve timing control solenoid valve.
LU-5, "Engine Lubrication System"
a. Remove components between intake valve timing intermediate lock control solenoid valve, intake valve
timing control solenoid valve, exhaust valve timing control solenoid valve and camshaft sprocket (INT) or
camshaft sprocket (EXH), (if necessary) and then check each oil groove for clogging.
b. Clean oil groove if necessary. Refer to
LU-5, "Engine Lubrication System"
6. After inspection, install the remaining components in the reverse order of removal.
ALBIA0909GB
VALVE TIMING CONTROL
EM-79
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
VALVE TIMING CONTROL
Exploded View
INFOID:0000000011279969
Intake Valve Timing Intermediate Lock Control Solenoid Valve, Intake Valve Timing
Control Solenoid Valve, and Exhaust Valve Timing Control Solenoid Valve
INFOID:0000000011279970
REMOVAL
1. Disconnect the battery negative terminal. Refer to
2. Remove cowl top extension. Refer to
EXT-25, "Removal and Installation"
3. Remove the RH engine mount torque rod. Refer to
4. Use a suitable jack (A) to securely support the bottom of the
engine (1) and the transaxle assembly (2).
CAUTION:
Put a piece of wood or an equivalent as the supporting sur-
face and secure in a stable condition.
5. Remove A/C line bracket bolt.
6. Remove harness grounds from engine mounting bracket (RH).
7. Remove harness retainers from engine mounting bracket (RH).
8. Remove the engine mounting bracket (RH). Refer to
9. Remove the RH engine mounting support bracket. Refer to
.
10. Remove the RH engine mount torque rod. Refer to
11. Disconnect harness connectors from intake valve timing intermediate lock control solenoid valve, intake
valve timing control solenoid valve, and exhaust valve timing control solenoid valve connectors.
1.
Valve timing cover
2.
O-rings
3.
Intake valve timing intermediate
lock control solenoid valve
4.
Intake valve timing control sole-
noid valve
5.
Exhaust valve timing control so-
lenoid valve
AWBIA1319GB
ALBIA0894GB
EM-80
< REMOVAL AND INSTALLATION >
VALVE TIMING CONTROL
12. Remove intake valve timing intermediate lock control solenoid valve, intake valve timing control solenoid
valve, and exhaust valve timing control solenoid valve bolts.
13. Remove intake valve timing intermediate lock control solenoid valve, intake valve timing control solenoid
valve, exhaust valve timing control solenoid valve from valve timing control cover.
14. Remove O-rings from intake valve timing intermediate lock control solenoid valve, intake valve timing con-
trol solenoid valve, and exhaust valve timing control solenoid valve.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-rings.
• Lubricate O-rings with clean engine oil before installing.
Valve Timing Control Cover
INFOID:0000000011279971
REMOVAL
1. Remove the intake valve timing intermediate lock control solenoid valve, intake valve timing control sole-
noid valve, exhaust valve timing control solenoid valve. Refer to
EM-79, "Intake Valve Timing Intermediate
.
2. Remove harness grounds and retainers from the top if the engine mount bracket.
3. Loosen the valve timing control cover bolts in the reverse order
shown.
a. Remove the valve timing control cover bolts.
b. Remove the valve timing control cover by cutting the liquid gas-
ket using Tool (A).
NOTE:
Do not loosen screws (A) on the back of the valve timing control
cover.
ALBIA0839GB
Tool number
: KV10111100 (J-37228)
AWBIA1257GB
AWBIA1361ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст