Nissan Rogue. Instruction — part 579
VALVE TIMING CONTROL
EM-81
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
INSTALLATION
1. Install valve timing control cover with the following procedure.
a. Install intake valve timing intermediate lock control solenoid valve, intake valve timing control solenoid
valve and exhaust valve timing control solenoid valve to valve timing control cover.
b. Install O-ring to front cover side.
CAUTION:
Do not reuse O-ring.
c. Apply liquid gasket to the positions shown. Refer to
ommended Chemical Products and Sealants"
d. Install valve timing control cover.
• Tighten the bolts to specification in the numerical order shown.
Diameter (A)
: 3.4 - 4.4 mm (0.134 - 0.173 in)
AWBIA1362ZZ
ALBIA0839GB
EM-82
< REMOVAL AND INSTALLATION >
OIL SEAL
OIL SEAL
VALVE OIL SEAL
VALVE OIL SEAL : Removal and Installation
INFOID:0000000011279972
REMOVAL
1. Remove camshafts. Refer to
EM-69, "Removal and Installation"
2. Remove valve lifters. Refer to
EM-61, "Disassembly and Assembly"
.
3. Rotate crankshaft, and set piston whose valve oil seal is to be removed to TDC. This will prevent valve
from dropping into cylinder.
CAUTION:
When rotating crankshaft, be careful to avoid scarring front cover with timing chain.
4. Remove valve collet.
• Compress valve spring using suitable tool (A). Remove valve
collet with a magnet.
CAUTION:
• Be careful not to damage valve lifter holes.
• Install suitable tool (A) in the center of valve spring
retainer (1) to press it.
5. Remove valve spring retainer and valve spring (with valve spring seat).
CAUTION:
Do not remove valve spring seat from valve spring.
6. Remove valve oil seal using suitable tool (A).
INSTALLATION
1. Apply new engine oil to valve oil seal joint surface and seal lip.
PBIC3209J
JSBIA3390ZZ
ALBIA0863GB
OIL SEAL
EM-83
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2. Press in valve oil seal to the height “H” as shown using suitable
tool (A).
3. Installation of the remaining components is in the reverse order of removal.
FRONT OIL SEAL
FRONT OIL SEAL : Removal and Installation
INFOID:0000000011279973
REMOVAL
1. Remove engine undercover. Refer to
EXT-37, "ENGINE UNDER COVER : Removal and Installation"
.
2. Remove front fender protector. Refer to
EXT-28, "FENDER PROTECTOR : Removal and Installation"
3. Remove drive belt. Refer to
EM-15, "Removal and Installation"
.
4. Remove crankshaft pulley (1) using the following procedure:
a. Hold the crankshaft pulley (1) using suitable tool (A), then
loosen and remove the crankshaft pulley bolt.
b. Attach suitable tool (A) in the threaded hole on crankshaft pulley
(1), and remove crankshaft pulley.
5. Remove front oil seal with a suitable tool.
CAUTION:
Do not damage front cover and crankshaft.
INSTALLATION
Height “H”
: Refer to
ALBIA0864GB
ALBIA0857GB
ALBIA0858GB
SEM829E
EM-84
< REMOVAL AND INSTALLATION >
OIL SEAL
1. Apply new engine oil to seal lip.
2. Install front oil seal so that each seal lip is oriented as shown.
• Press-fit front oil seal until it is flush with front end surface of
front cover using a suitable drift (A).
CAUTION:
• Do not damage front cover and crankshaft.
• Press-fit oil seal straight to avoid causing burrs or tilt-
ing.
• Do not touch the grease applied to the oil seal lip.
• Do not reuse oil seal.
3. Insert crankshaft pulley (2) by aligning with crankshaft key.
• Tap its center with a plastic hammer to insert.
• Do not tap the crankshaft pulley outer diameter.
4. Tighten crankshaft pulley bolt.
• Secure crankshaft pulley with suitable tool to tighten the bolt.
• Perform angle tightening with the following procedure.
a. Apply new engine oil to threads and seat surfaces of bolts.
b. Apply a paint mark (A) on the front cover, mating with any one of
six easy to recognize stamp marks on bolt flange (B).
c.
Tighten crankshaft bolt (1) to specification.
NOTE:
Check that the assembled unit does not interfere with adjacent components by turning the crankshaft in
the tightening direction.
5. Installation of the remaining components is in the reverse order of removal.
REAR OIL SEAL
REAR OIL SEAL : Removal and Installation
INFOID:0000000011279974
REMOVAL
1. Remove the engine and transaxle. Refer to
EM-86, "Removal and Installation (FWD)"
"Removal and Installation (AWD)"
2. Separate engine from transaxle.
3. Remove drive plate. Refer to
4. Remove rear oil seal with a suitable tool.
CAUTION:
Be careful not to damage crankshaft and cylinder block.
(A)
: Dust seal lip
(B)
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
ALBIA0865GB
Step 1
: 42.1 N·m (4.3 kg-m, 31 ft-lb)
Step 2
: Turn crankshaft bolt (1) an additional 60
° +6°/
-0
°.
ALBIA0862GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст