Nissan Rogue. Instruction — part 418
DLN-116
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
ELECTRIC CONTROLLED COUPLING
7. Remove wave spring (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When replacing electric controlled coupling, perform writing unit characteristic. Refer to
• Do not reuse hose clamp and breather connector.
• Make sure there are no pinched or restricted areas on the breather hose caused by bending or wind-
ing when installing it.
• Install the hose clamp at the final drive side, with the paint mark facing to the vehicle front.
• Install the hose clamp at the suspension member side, with the tab facing downward.
• Use Genuine Silicone RTV or an equivalent. Refer to
GI-22, "Recommended Chemical Products and
• Remove the old sealant from mating surfaces using a suitable tool before installing.
• Apply liquid gasket (1) to mating surface of coupling cover.
Use Genuine Silicone RTV or equivalent. Refer to
mended Chemical Products and Sealants"
.
CAUTION:
• The width of sealant bend is approximately 3 mm (0.012 in).
• Installation should be done within 5 minutes after applying
liquid gasket.
• Do not fill the engine within engine oil for at least 30 minutes
after the components are installed to allow the sealant to
cure.
• Install electric controlled coupling to spline of drive pinion inside final drive assembly.
CAUTION:
• Align the pin (A) on electric controlled coupling with the
groove (B) of final drive assembly.
• Be careful not to damage center oil seal.
(2) : Rear final drive assembly
ALDIA0517ZZ
JSDIA3059ZZ
JSDIA3060ZZ
ELECTRIC CONTROLLED COUPLING
DLN-117
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Press the electric controlled coupling pin to check that it is posi-
tioned in the groove of the final drive assembly as shown.
NOTE:
If the pin is properly positioned in the groove, then the electric con-
trolled coupling can be pressed into position by the same amount
of flection of the wave spring.
• Temporarily tighten reamer bolts (1) to the positions shown.
CAUTION:
• Do not use tools. Always tighten by hand.
• If reamer bolts cannot be tightened all the way by hand, the
electric controlled coupling pin may not be positioned in the
groove of the final drive assembly. In this case, remove elec-
tric controlled coupling and reinstall it.
• If reamer bolts can be tightened all the way by hand torque them to
the specified value.
• When oil leaks while removing, check oil level after the installation. Refer to
JSDIA3068ZZ
JSDIA3061ZZ
DLN-118
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
AIR BREATHER
AIR BREATHER
Exploded View
INFOID:0000000011278414
*: These parts are adhered to each other. Therefore they are assembled parts.
Removal and Installation
INFOID:0000000011278415
REMOVAL
1. Remove clip (A) from rear suspension member (1).
2. Remove air breather hose (2) and breather tube (4) together.
3. Loosen hose clamp and remove breather tube (4) from air
breather hose (2).
Breather connector (resin)
Trim clip
Bracket
Hose clamp
Air breather hose
Breather connector (metal)
Breather connector (resin)
Air breather hose
Clip
Hose connector
Air breather hose*
Air breather tube*
Air breather hose*
Breather connector (metal)
Rear final drive assembly
: Always replace after every disassembly.
JSDIA5188GB
(3) : Rear final drive assembly
: Front
ALDIA0512ZZ
AIR BREATHER
DLN-119
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4. Remove clips (A) from rear suspension member (3).
5. Remove hose clamp (1) and clip (B) from air breather hose (4).
6. Remove air breather hose (4).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse hose clamps.
• Do not reuse trim clips.
• Do not reuse breather connectors (metal).
• Do not reuse clips.
• Set breather connector (1) to rear final drive with the paint mark (A)
facing front as shown.
• When installing air breather hose, make sure there are no pinched
or restricted areas on air breather hose caused by bending or
winding.
(2) : Electric controlled coupling
: Front
ALDIA0513ZZ
: Front
AWDIA1155ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст