Nissan Rogue. Instruction — part 419
DLN-120
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
REAR FINAL DRIVE ASSEMBLY
UNIT REMOVAL AND INSTALLATION
REAR FINAL DRIVE ASSEMBLY
Exploded View
INFOID:0000000011278416
Removal and Installation
INFOID:0000000011278417
REMOVAL
1. Remove rear propeller shaft. Refer to
2. Remove rear drive shafts. Refer to
.
3. Disconnect AWD solenoid harness connector.
4. Remove rear final drive breather hose and electric controlled coupling breather hose.
.
5. Support final drive assembly with a suitable jack.
6. Remove final drive nuts and final drive bolts with power tool.
If necessary, remove final drive bracket and washer with power tool.
CAUTION:
Secure final drive assembly to a suitable jack while removing it.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When replacing rear final drive assembly, perform writing unit characteristics. Refer to
.
When oil leaks while removing final drive assembly, check oil level after the installation. Refer to
Final drive mounting bracket
Mounting stopper
Rear final drive assembly
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSDIA5398GB
ELECTRIC CONTROLLED COUPLING
DLN-121
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
ELECTRIC CONTROLLED COUPLING
Exploded View
INFOID:0000000011278418
Stud bolt
Connector bracket
Reamer bolt
Electric controlled coupling assem-
bly
Wave spring
Drive pinion oil seal
Drive pinion lock nut
Pinion front bearing
Gear carrier
Collapsible spacer
Drive pinion adjusting shim
Pinion rear bearing
Drive pinion
Drive gear
Differential case
Side bearing
Side bearing adjusting shim
Side oil seal
Rear cover
Stud bolt
Gasket
Drain plug
Filler plug
Pinion mate thrust washer
Pinion mate gear
Side gear thrust washer
Side gear
Pinion mate shaft
Lock pin
Oil seal lip
Screw hole
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
: Select with proper thickness.
: Apply gear oil.
JSDIA5442GB
DLN-122
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
ELECTRIC CONTROLLED COUPLING
Disassembly and Assembly
INFOID:0000000011278419
DISASSEMBLY
1. Remove stud bolts .
2. Remove electric controlled coupling assembly from final drive
assembly.
3. Remove wave spring.
4. Remove drive pinion oil seal from the inside of gear carrier.
DLN-137, "Disassembly and Assembly"
CAUTION:
When removing electric controlled coupling, replace drive
pinion oil seal.
5. Remove connector bracket from electric controlled coupling.
6. Separate band clip and connector clip from connector bracket.
ASSEMBLY
*: Apply anti-corrosion oil.
: Apply multi purpose grease.
: Apply Genuine Silicone RTV or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
: Apply Genuine High Strength Thread Locking Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products
JSDIA5282ZZ
JSDIA5250ZZ
JSDIA5234ZZ
JSDIA5241ZZ
ELECTRIC CONTROLLED COUPLING
DLN-123
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
1. Install connector bracket to electric controlled coupling.
• For tightening torque, refer to
2. Fix AWD solenoid harness with band clip and connector clip.
3. Install drive pinion oil seal to the inside of gear carrier. Refer to
DLN-137, "Disassembly and Assembly"
CAUTION:
When removing electric controlled coupling, replace drive
pinion oil seal.
4. Install wave spring to the inside of gear carrier.
5. Apply liquid gasket to mating surface of electric controlled cou-
pling assembly.
CAUTION:
• Remove old gasket adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adher-
ing to the mounting surfaces.
• The width of sealant bead is approximately 3 mm (0.12 in).
Apply sealant evenly.
6. Match electric controlled coupling assembly to spline of drive
pinion, then install it to final drive assembly .
CAUTION:
Be careful not to damage drive pinion oil seal.
JSDIA5241ZZ
JSDIA5236ZZ
JSDIA5242ZZ
JSDIA5260ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст