Nissan Rogue. Instruction — part 946
PCS-30
< WIRING DIAGRAM >
[IPDM E/R]
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
AAMIA2836GB
PCS
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PCS-31
< WIRING DIAGRAM >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
AAMIA2837GB
PCS-32
< BASIC INSPECTION >
[IPDM E/R]
ADDITIONAL SERVICE WHEN REPLACING IPDM E/R
BASIC INSPECTION
ADDITIONAL SERVICE WHEN REPLACING IPDM E/R
Description
INFOID:0000000011277081
After replacing IPDM E/R, it is necessary to perform control unit configuration and height sensor initialize (For
LED headlamp models) with CONSULT.
Work Procedure
INFOID:0000000011277082
1.
REPLACE IPDM E/R
Replace IPDM E/R. Refer to
PCS-40, "Removal and Installation"
>> GO TO 2.
2.
WRITING VEHICLE SPECIFICATION (IPDM E/R)
CONSULT Configuration
Perform “After Replace ECU” of “Read/Write Configuration” or “Instruction Configuration” to write vehicle specifi-
cation. Refer to
.
>> GO TO 3.
3.
CHECK HEADLAMP TYPE
Check headlamp type.
LED headlamp>>GO TO 4.
Halogen headlamp>>Work End.
4.
HEIGHT SENSOR INITIALIZE
Perform height sensor initialize. Refer to
EXL-221, "SENSOR INITIALIZE : Special Repair Requirement"
>> Work End.
PCS
CONFIGURATION (IPDM E/R)
PCS-33
< BASIC INSPECTION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CONFIGURATION (IPDM E/R)
Description
INFOID:0000000011277083
There is no vehicle specification in new IPDM E/R, so the vehicle specification needs to be written in IPDM E/
R with CONSULT.
CAUTION:
• When replacing IPDM E/R, always perform “Instruction Configuration” with CONSULT. Or not doing so,
IPDM E/R control function does not operate normally.
• Never perform “Instruction Configuration” except for new IPDM E/R or the control function may not
operate normally.
Work Procedure
INFOID:0000000011277084
1.
WRITING MODE SELECTION
CONSULT Configuration
Select “CONFIGURATION” of IPDM E/R.
>> GO TO 2.
2.
PERFORM “MANUAL CONFIGURATION”
CONSULT Configuration
1. Select “MANUAL CONFIGURATION”.
2. Identify the correct model and configuration list. Refer to
.
CAUTION:
• Thoroughly read and understand the vehicle specification. ECU control may not operate nor-
mally if the setting is not correct.
• Make sure to select “SETTING” even if the indicated configuration of brand new IPDM E/R is
same as the desirable configuration. If not, configuration which is set automatically by selecting
vehicle model cannot be memorized
3. Sets the displayed item and then select “NEXT”.
NOTE:
If item is not displayed, select “NEXT”.
4. Check that the configuration has been successfully written and touch “End”.
>> GO TO 3.
3.
OPERATION CHECK
Confirm that each function controlled by IPDM E/R operates normally.
>> Work End.
Configuration list
INFOID:0000000011277085
CAUTION:
Check vehicle specifications before servicing.
IPDM E/R
Type ID
How to identify Type ID
Key type
HEAD LAMP type
284B7-4BA1A
non Intelligent Key
Halogen
284B7-4BA1B
Intelligent Key
Halogen
284B7-4BA1C
Intelligent Key
LED
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст