Nissan Rogue. Instruction — part 1019
RF-56
< REMOVAL AND INSTALLATION >
MOONROOF UNIT ASSEMBLY
• Always work with a helper.
• Handle glass lid with care to prevent damage.
NOTE:
• For easier and more accurate installation, always mark each point before removal.
• After any adjustment, check moonroof operation and glass lid alignment.
Unit: mm (in)
Gap adjustment (Front and Rear)
1. Open sunshade (1).
: Front
2. Tilt glass lid up, then release side trim cover (2) on each side
and set aside.
NOTE:
LH side shown; RH similar.
3. Loosen glass lid bolts (A) (two each on LH and RH side), then tilt
glass lid down.
4. Instructionly adjust glass lid from outside of vehicle until gaps A-A
and C-C are within specification.
NOTE:
Temporarily loosely tighten glass lid bolts to prevent movement between each adjustment.
5. Tilt glass lid up and down several times using moonroof switch to check that it operates smoothly.
1.
Roof panel
2.
Weatherstrip
3.
Glass lid/panoramic roof glass
Front
ALKIA3675ZZ
Portion
Gap
Surface height difference
D
E
F
A-A
1.4
± 0.8 (0.06 ± 0.03)
7.3
± 0.8 (0.29 ± 0.03)
0.7
± 1.5 (0.03 ± 0.06)
B-B
1.4
± 0.8 (0.06 ± 0.03)
7.3
± 0.8 (0.29 ± 0.03)
0.7
± 1.5 (0.03 ± 0.06)
C-C
1.4
± 0.8 (0.06 ± 0.03)
7.3
± 0.8 (0.29 ± 0.03)
0.7
± 1.5 (0.03 ± 0.06)
ALKIA0059ZZ
MOONROOF UNIT ASSEMBLY
RF-57
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
6. Tilt glass lid up and tighten bolts.
NOTE:
First tighten left front bolt, then right rear bolt on glass lid to prevent uneven torque while tightening
remaining bolts.
7. Attach side trim covers (LH/RH), then tilt glass lid down.
Gap Adjustment (Sides)
The moonroof unit assembly is mounted on locator pins and adjustment from side to side cannot be per-
formed.
Surface Height Adjustment
1. Tilt glass lid up and down several times using moonroof switch to check that it operates smoothly.
2. Check height difference between roof surface and glass lid surface, then compare to specifications.
3. If necessary, adjust height difference by using the following procedure.
• Loosen glass lid bolts.
• Instructionly raise/lower glass lid until height difference is within specification.
NOTE:
If necessary, shims may be added between moonroof unit assembly and roof to increase adjustment
range. Refer to
RF-50, "Removal and Installation"
Temporarily loosely tighten moonroof unit assembly bolts to prevent movement between each adjust-
ment.
• Tilt glass lid up and down several times using moonroof switch to check that it operates smoothly.
• Tighten glass lid and moonroof side bracket bolts.
NOTE:
First tighten left front bolt, then right rear bolt on glass lid to prevent uneven torque while tightening
remaining bolts.
• After any adjustment, check moonroof operation and glass lid alignment.
RF-58
< REMOVAL AND INSTALLATION >
MOONROOF UNIT ASSEMBLY
Exploded View
INFOID:0000000011280169
Removal and Installation
INFOID:0000000011280170
REMOVAL
CAUTION:
• Always work with a helper.
• When taking moonroof unit assembly out, use cloths to protect the seats and trim from damage.
1. Remove headlining. Refer to
INT-30, "Removal and Installation"
1.
Sunshade cable (LH/RH)
2.
Glass lid cable (LH/RH)
3.
Wind deflector
4.
Glass lid
5.
Glass lid weatherstrip
6.
Side trim cover (LH/RH)
7.
Front drain hose (LH/RH)
8.
Moonroof motor assembly
9.
Sunshade motor assembly
10. Moonroof front bracket (LH/RH)
11. Moonroof rear bracket (LH/RH)
12. Cable guide (LH/RH)
13. Moonroof unit assembly
14. Rear drain hose (LH/RH)
15. Rear trim covers (LH/RH)
16. Panoramic roof glass
17. Panoramic roof glass weatherstrip
18. Sunshade
Front
AWJIA1645ZZ
MOONROOF UNIT ASSEMBLY
RF-59
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
2. Disconnect drain hoses (front/rear) from moonroof unit assembly. Refer to
.
3. Disconnect harness connectors from moonroof motor assembly and sunshade motor assembly.
4. Remove nuts, then using a helper carefully lift each side and remove moonroof unit assembly out back of
vehicle.
WARNING:
Bodily injury may occur if moonroof unit assembly is not supported properly when removing.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installing the moonroof unit assembly, perform the leak test and check that there is no air or
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст