Nissan Rogue. Instruction — part 1018
RF-52
< REMOVAL AND INSTALLATION >
MOONROOF MOTOR ASSEMBLY
MOONROOF MOTOR ASSEMBLY
Exploded View
INFOID:0000000011280166
Removal and Installation
INFOID:0000000011280167
REMOVAL
1. Close glass lid.
1.
Sunshade cable (LH/RH)
2.
Glass lid cable (LH/RH)
3.
Wind deflector
4.
Glass lid
5.
Glass lid weatherstrip
6.
Side trim cover (LH/RH)
7.
Front drain hose (LH/RH)
8.
Moonroof motor assembly
9.
Sunshade motor assembly
10. Moonroof front bracket (LH/RH)
11. Moonroof rear bracket (LH/RH)
12. Cable guide (LH/RH)
13. Moonroof unit assembly
14. Rear drain hose (LH/RH)
15. Rear trim covers (LH/RH)
16. Panoramic roof glass
17. Panoramic roof glass weatherstrip
18. Sunshade
Front
AWJIA1645ZZ
MOONROOF MOTOR ASSEMBLY
RF-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
2. Remove the headlining. Refer to
INT-30, "Removal and Installation"
.
3. Remove moonroof motor assembly screws (1).
Front
4. Disconnect harness connector (A) and remove moonroof motor
assembly (2) from moonroof unit assembly front end rail.
CAUTION:
Do not run the removed moonroof motor assembly as a sin-
gle unit.
INSTALLATION
1. Move moonroof motor assembly laterally little by little so that the gear is completely engaged into the wire
on the moonroof unit assembly, and the mounting surfaces become parallel. Install the moonroof motor
assembly screws and tighten.
CAUTION:
Before installing the motor, be sure to place the link and wire assembly in the symmetrical and
fully closed position.
NOTE:
If necessary, insert a suitable tool into the drive key and rotate right or left slightly to assist in complete
moonroof motor gear alignment.
2. Remainder of installation is in the reverse order of removal.
3. Synchronize moonroof motor assembly with moonroof unit assembly. Refer to
SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
.
ALKIA3464ZZ
RF-54
< REMOVAL AND INSTALLATION >
MOONROOF UNIT ASSEMBLY
MOONROOF UNIT ASSEMBLY
Inspection
INFOID:0000000011280168
WIND DEFLECTOR
1. Open glass lid fully.
2. Visually check for proper installation, damaged/deteriorated components, or foreign objects within mecha-
nism. Correct as required for smooth operation.
3. Check for grease at the wind deflector arm (1) and pivot areas. If
necessary, apply a sufficient amount of grease for non-binding
operation.
Front
4. Check that the wind deflector (1) moves freely within the moon-
roof unit assembly while instructionly pressing down and releasing.
If a malfunction is detected, remove the moonroof unit assembly
and visually inspect. If damage is found, replace either wind
deflector (1) or moonroof unit assembly as required. Refer to
RF-61, "Removal and Installation"
(WIND DEFLECTOR) or
58, "Removal and Installation"
(MOONROOF UNIT ASSEM-
BLY).
Front
LINK AND WIRE ASSEMBLY
NOTE:
Before replacing a suspect part, make sure it is the source of noise being experienced.
1. Check link to determine if coating film has peeled off excessively enough that substrate is visible. Check
also to determine if link is the source of noise. Replace as necessary.
2. Visually check to determine if a sufficient amount of grease has been applied to wire or rail groove. If not,
add grease as required.
3. Check wire for any damage or deterioration. If any damage is found, replace moonroof unit assembly.
RF-58, "Removal and Installation"
WEATHERSTRIP
1. Visually check weatherstrip for damage, deterioration, or deformation.
• Open glass lid partially to inspect front edge of weatherstrip.
• Tilt up glass lid fully to inspect sides and rear edge of weatherstrip.
If any area of the weatherstrip is found to be damaged, replace the glass lid. Refer to
2. Check for leaks around glass lid.
• Close glass lid.
• Pour water around surface to determine area of concern.
- For gaps or misalignment, adjust glass lid to specifications. Refer to ADJUSTMENT in this section.
- For damaged sealing surfaces, either replace glass lid, refer to
RF-50, "Removal and Installation"
repair the panel.
DRAIN HOSES
ALJIA1504ZZ
WIIA0849E
MOONROOF UNIT ASSEMBLY
RF-55
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
1. Remove the headlining. Refer to
INT-30, "Removal and Installation"
2. From the inside front pillar (3) visually check drain hoses (1) for:
• Proper connection at moonroof unit assembly (4) and drain
hose connection at the exit base (2).
• Damage, pinch, cracks, deterioration.
Front
3. Pour water through drain hoses to determine watertight performance.
If damaged or leaking portions in any drain hose is found, replace entire drain hose as necessary.
4. From the inside of the rear quarter panel (1) visually check drain
hoses (2) for damage, pinching, cracks, or deterioration.
5. Check for proper connection at moonroof unit assembly (3) and
drain hose (2) and for proper routing along the rear inner quarter
panel (1).
Front
ADJUSTMENT
CAUTION:
1.
Front pillar
2.
Moonroof unit assembly
3.
Rear pillar
4.
Rear drain hoses (LH/RH)
5.
Front drain hoses (LH/RH)
ALKIA3460ZZ
ALKIA3461ZZ
ALKIA3462ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст