Nissan Rogue. Instruction — part 352
DLK-250
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000011279008
REMOVAL
1. Remove front fender. Refer to
DLK-245, "Removal and Installation"
2. Remove front door assembly. Refer to
DLK-247, "DOOR ASSEMBLY : Removal and Installation"
.
3. Remove front door hinge bolts (body side) and front door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten nuts/bolts to specified torque. Refer to
• Apply anticorrosive agent to the hinge mating surface.
• After installation, check front door open/close and lock/unlock operation.
• Check door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After installation, perform the front door adjustment procedure. Refer to
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000011279009
REMOVAL
1. Fully close the front door window.
2. Remove front door speaker. Refer to
AV-70, "Removal and Installation"
(DISPLAY AUDIO),
(NAVIGATION WITHOUT BOSE) or
AV-374, "Removal and Installation"
(NAV-
IGATION WITH BOSE).
3. Remove door check link bolt (body side).
4. Remove door check link bolts (door side).
5. Remove door check link through the hole in door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten nuts/bolts to specified torque. Refer to
• After installation, check front door open/close and lock/unlock operation.
• Check door check link rotating point for poor lubrication. If necessary, apply a suitable multi-pur-
pose grease.
2015 Rogue NAM
REAR DOOR
DLK-251
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR
Exploded View
INFOID:0000000011279010
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000011279011
CAUTION:
• Use two people when removing or installing the rear door due to its heavy weight.
• When removing and installing rear door assembly, support rear door using a suitable tool.
REMOVAL
1. Remove rear door finisher. Refer to
INT-18, "Removal and Installation"
.
2. Remove rear door vapor barrier (1).
NOTE:
LH side shown; RH similar.
3. Disconnect the harness connectors from rear door.
4. Remove harness grommet from rear door, then pull out rear door harness from the rear door.
1.
Rear door panel
2.
Grommet
3.
Bumper rubber
4.
Door striker
5.
Door check link
6.
Rear door lower hinge
7.
Rear door upper hinge
AWKIA2928ZZ
ALKIA3481ZZ
2015 Rogue NAM
DLK-252
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
5. Remove rear door check link bolt (body side).
6. Remove rear door hinge nuts (door side) and rear door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten nuts/bolts to specification. Refer to
• Apply anticorrosive agent where necessary.
• After installation, check rear door open/close and lock/unlock operation.
• After installation, perform the rear door adjustment procedure. Refer to
.
DOOR ASSEMBLY : Adjustment
INFOID:0000000011279012
Check the clearance and surface height between rear door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dures.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
Rear door upper hinge
7.
Rear door lower hinge
F.
Door striker bolts
AWKIA2917ZZ
2015 Rogue NAM
REAR DOOR
DLK-253
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit: mm (in)
1. Remove center pillar lower finisher. Refer to
INT-22, "CENTER PILLAR LOWER FINISHER : Removal
2. Loosen rear door hinge nuts (door side).
3. Adjust the surface height of rear door according to specifications provided.
4. Temporarily tighten rear door hinge nuts (door side).
5. Loosen rear door hinge nuts and bolts (body side).
6. Raise rear door at rear end to adjust clearance of rear door according to the specifications provided.
7. After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• Check rear door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-pur-
pose grease.
• After adjusting, apply touch-up paint (body color) to the head of rear door hinge bolts and nuts.
8. Install center pillar lower finisher. Refer to
INT-22, "CENTER PILLAR LOWER FINISHER : Removal and
.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000011279013
REMOVAL
Remove bolts and rear door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse rear door striker bolts.
• Tighten bolts to specification. Refer to
• After installation, check rear door open/close operation. If necessary, adjust the door striker. Refer to
DLK-253, "DOOR STRIKER : Adjustment"
DOOR STRIKER : Adjustment
INFOID:0000000011279014
DOOR STRIKER ADJUSTMENT
1. Loosen door striker bolts
2. Adjust door striker so that it becomes parallel with front door lock
insertion direction.
3. Tighten door striker bolts to specification. Refer to
.
Portion
Section
Measurement
Standard
Front fender - Front door
A – A
Clearance
4.0
± 1.0 (0.16 ± 0.04)
Surface height
± 1.0 (± 0.04)
Front door - Rear door
B – B
Clearance
4.3
± 1.0 (0.17 ± 0.04)
Surface height
± 1.0 (± 0.04)
Rear door - Body side outer
C – C
Clearance
3.7
± 1.0 (0.15 ± 0.04)
Surface height
± 1.0 (± 0.04)
PIIB2804J
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст