Nissan Rogue. Instruction — part 1054
SE-82
< UNIT DISASSEMBLY AND ASSEMBLY >
THIRD ROW SEAT
THIRD ROW SEAT
Exploded View
INFOID:0000000011280478
1.
Seatback board (RH)
2.
Seatback trim (RH)
3.
Seatback pad (RH)
4.
Seat cushion trim (RH)
5.
Seat cushion pad (RH)
6.
Seat cushion silencer (LH/RH)
7.
Seat hinge finisher (RH)
8.
Gas stay
9.
Bolt cover (RH)
AWJIA1319ZZ
THIRD ROW SEAT
SE-83
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Seatback
INFOID:0000000011280479
DISASSEMBLY
NOTE:
LH shown : RH similar
1. Remove third row seat. Refer to
SE-43, "Removal and Installation"
.
2. Remove headrest.
3. Remove screws (A) and third row seat cross member finishers
(1, 2, 3).
4. Release seatback pull strap stop using a suitable tool.
5. Release third row luggage board outer clips (A) and inner clips
(B) using a suitable tool.
10. Seat belt buckle (RH)
11. Seat belt buckle (LH)
12. Bolt cover (LH)
13. Stopper pin
14. Seat frame support
15. Seat hinge finisher (LH)
16. Seat striker (LH/RH)
17. Seat striker finisher (LH/RH)
18. Seatback pull strap (LH/RH)
19. Seatback frame (LH)
20. Headrest (LH/RH)
21. Third row seat cross member
22. Third row seat cross member fin-
isher (LH)
23. Third row seat cross member
finisher (center)
24. Third row seat cross member fin-
isher (RH)
25. Third row luggage floor
26. Seatback board (LH)
27. Seatback trim (LH)
28. Seatback pad (LH)
29. Seat cushion trim (LH)
30. Seat cushion pad (LH)
31. Seat frame finisher (center)
32. Seat cushion frame (LH)
33. Seat cushion frame (RH))
34. Headrest holder (locked)
35. Headrest holder (free)
36. Seatback frame (RH)
Clip
Pawl
ALJIA1427ZZ
ALJIA1429ZZ
SE-84
< UNIT DISASSEMBLY AND ASSEMBLY >
THIRD ROW SEAT
6. Release third row luggage board retainer strap clips (A) (LH/RH)
using a suitable tool and remove third row luggage board.
7. Release clips using a suitable tool then gently pull seatback
board (1) forward and out and remove as shown (
).
CAUTION:
After removing the seatback board, check the orientation of
clips. Improper installation of clips could result in damage
to the seatback board.
: Clip
8. Reinstall clips in proper locations on the seatback board.
9. Remove screws (A) and remove seat hinge finisher (1).
10. Release J-hooks from seat frame and remove seatback trim and
seatback pad as an assembly.
ALJIA1430ZZ
ALJIA1431ZZ
ALJIA1433ZZ
ALJIA1435ZZ
THIRD ROW SEAT
SE-85
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
11. Reach up behind the seatback pad, release the headrest holder
locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing headrest holder, check its orien-
tation (front/rear and right/left).
12. Release hook and loop finisher and remove hog rings, then sep-
arate seatback trim from seatback pad.
NOTE:
Remove all pieces of hog rings and discard them.
: Hog ring
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat-
back trim and seatback pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Make sure hook fastener is pressed into place after seatback trim
is assembled.
• Smooth out all wrinkles during assembly.
Seat Cushion
INFOID:0000000011280480
DISASSEMBLY
NOTE:
LH shown, RH similar.
1. Remove third row seat. Refer to
SE-43, "Removal and Installation"
.
2. Remove third row seat cross member. Refer to
SE-44, "Third Row Seat Cross Member"
PIIB4084J
ALJIA1434ZZ
PIIB3356J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст