Nissan Rogue. Instruction — part 1052
SE-74
< UNIT DISASSEMBLY AND ASSEMBLY >
SECOND ROW SEAT
4. Remove bolts (A) and armrest.
5. Release pawls and remove recline handle finisher.
6. Release pawls and remove seatbelt retractor outer finisher.
7. Remove seat belt retractor (center) bottom anchor bolt then route seat belt retractor (center) through sec-
ond row seat cushion and seatback.
8. Release J-hooks (A) then release fastener (B) and remove seat-
back pad and seatback trim.
9. Remove screw (A), then using a suitable tool release pawl and
remove the armrest inner finisher (1).
: Pawl
10. Remove screw (A), then remove recline device (1) from seat-
back frame.
ALJIA1412ZZ
ALJIA1448ZZ
ALJIA1462ZZ
ALJIA1463ZZ
SECOND ROW SEAT
SE-75
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
11. Release EZ entry cable (1) from recline device (A) and seatback
frame (B), then remove the EZ entry cable.
CAUTION:
Note the cable routing for correct installation.
: Front
ASSEMBLY
Assembly is in reverse order of disassembly.
CAUTION:
Make sure to route cables correctly for proper function.
LH SEAT : Seat Slide Release Cable
INFOID:0000000011280475
DISASSEMBLY
NOTE:
LH seat shown, RH seat similar.
1. Remove second row seat. Refer to
SE-39, "Removal and Installation"
.
2. Using a suitable tool release clips and remove seatback board
(1).
: Clip
ALJIA1464ZZ
ALJIA1413ZZ
SE-76
< UNIT DISASSEMBLY AND ASSEMBLY >
SECOND ROW SEAT
3. Remove screw (A), then using a suitable tool release clips and
pawls and remove armrest finisher (1).
: Clip
: Pawl
4. Remove bolts (A) and armrest.
5. Release J-Hooks (A) and fasteners (B), then route seatbelt
buckles through seat cushion and remove seat cushion pad and
seat cushion trim.
6. Press headrest holder lock button, then lift headrest up and remove.
7. Reach up behind the seatback pad, release the headrest holder
locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing headrest holder, check its orien-
tation (front/rear and right/left).
8. Release pawls and remove recline handle finisher.
9. Release pawls and remove seatbelt retractor outer finisher.
ALJIA1411ZZ
ALJIA1412ZZ
ALJIA1452ZZ
PIIB4084J
SECOND ROW SEAT
SE-77
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
10. Release J-hooks (A) then release fastener (B) and remove seat-
back pad and seatback trim.
11. Using a suitable tool release clip (A) and remove the seat cush-
ion inner finisher LH (1).
NOTE:
Seatback frame removed for clarity.
: Front
12. Release seat slide release cable (1) ends from both LH side (A)
and RH side (B) of seat frame.
CAUTION:
Note the cable routing for correct installation.
: Front
13. Remove screw (A) and unclip seat cushion slide cable (1) from
seat cushion frame.
: Front
14. Unclip seat slide release cable clips from seat cushion frame and remove.
ASSEMBLY
Assembly is in reverse order of disassembly.
CAUTION:
Make sure to route cables correctly for proper function.
RH SEAT
RH SEAT : Seatback
INFOID:0000000011280476
DISASSEMBLY
ALJIA1448ZZ
ALJIA1459ZZ
ALJIA1460ZZ
ALJIA1461ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст