Nissan Rogue. Instruction — part 316
DLK-106
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORK FLOW
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES
>> GO TO 8.
NO
>> Check according to
GI-44, "Intermittent Incident"
.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO
>> Before returning the vehicle to the customer, always erase DTC.
2015 Rogue NAM
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
DLK-107
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL
Description
INFOID:0000000011278809
When the battery is disconnected from the negative terminal, it is necessary to perform initial setting to oper-
ate automatic back door control system normally.
NOTE:
The following specified operations are not performed under the non-initialized condition.
• Automatic back door open/close function
• Anti-pinch function
Work Procedure
INFOID:0000000011278810
1.
INITIALIZATION
1. Fully close the back door instructionly. (When back door is already fully closed, this operation is not neces-
sary).
2. Perform automatic back door open/close operation of back door.
3. Check for noise or malfunctioning during operation.
4. Check that hazard lamp blinks and that warning buzzer operates.
NOTE:
Never touch back door or allow foreign materials to be pinched in door when performing automatic back door
open/close operation of back door until it is in the fully closed or fully open position.
>> Inspection End.
2015 Rogue NAM
DLK-108
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
ADDITIONAL SERVICE WHEN REPLACING BCM
ADDITIONAL SERVICE WHEN REPLACING BCM
Description
INFOID:0000000011278811
Perform the system initialization when replacing BCM, replacing Intelligent Key or registering an additional
Intelligent Key.
Work Procedure
INFOID:0000000011278812
Refer to the CONSULT Immobilizer mode and follow the on-screen instructions.
2015 Rogue NAM
ADDITIONAL SERVICE WHEN REPLACING AUTOMATIC BACK DOOR CON-
TROL UNIT
DLK-109
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ADDITIONAL SERVICE WHEN REPLACING AUTOMATIC BACK DOOR
CONTROL UNIT
Description
INFOID:0000000011278813
When replacing control module or removing connector terminal, it is necessary to perform initial setting to
operate automatic back door system normally.
NOTE:
The following specified operations are not performed under the non-initialized condition:
• Automatic back door open/close function
• Anti-pinch function
Work Procedure
INFOID:0000000011278814
1.
INITIALIZATION
1. Fully close the back door instructionly. (When back door is already fully closed, this operation is not neces-
sary.)
2. Perform automatic back door open/close operation of back door.
3. Check for noise or malfunctioning during operation.
4. Check that hazard lamp blinks and that warning buzzer operates.
NOTE:
Never touch back door or allow foreign materials to be pinched in door when performing automatic back door
open/close operation of back door until it is in the fully closed or fully open position.
>> Inspection End.
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст