Nissan Rogue. Instruction — part 317
DLK-110
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
CALIBRATION OF AUTOMATIC BACK DOOR POSITION INFORMATION
CALIBRATION OF AUTOMATIC BACK DOOR POSITION INFORMATION
Description
INFOID:0000000011278815
When the following work is performed, it is necessary to perform initial setting of automatic back door position
information to operate automatic back door system:
• After removing and installing or replacing back door assembly.
• After removing and installing or replacing spindle unit.
• After adjustment or position change of the back door hinges or striker.
Work Procedure
INFOID:0000000011278816
1.
STEP 1
Fully close the back door instructionly.
>> GO TO 2.
2.
STEP 2
1. Select “AUTO BACK DOOR” using CONSULT.
2. Select “RESET AUTO BACK DOOR STATUS” of “Work support”.
3. Touch “START” to erase automatic back door position information.
>> GO TO 3.
3.
STEP 3
Operate back door opener switch and perform automatic open operation.
NOTE:
At this time, automatic operation of back door is performed at half speed.
>> GO TO 4.
4.
STEP 4
1. The back door fully opens.
2. Check that hazard warning lamp blinks and automatic back door warning buzzer sounds normally.
Does hazard warning lamp blink and automatic back door warning buzzer sound normally?
YES
>> GO TO 5.
NO
>> GO TO 1.
5.
STEP 5
Fully close the back door.
>> Inspection End.
2015 Rogue NAM
U1000 CAN COMM CIRCUIT
DLK-111
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000011377355
.
DTC Logic
INFOID:0000000011377356
DTC DETECTION LOGIC
NOTE:
U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm
that there are actual CAN diagnostic symptoms and a present DTC by performing the Self Diagnostic Result
procedure.
Diagnosis Procedure
INFOID:0000000011377357
1.
PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 second or more.
2. Check “Self Diagnostic Result”.
Is “CAN COMM CIRCUIT” displayed?
YES
>> Perform CAN Diagnosis as described in DIAGNOSIS section of CONSULT Operation Instruction.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
CONSULT Display
DTC Detection Condition
Possible cause
CAN COMM CIRCUIT
[U1000]
When any listed module cannot communicate with CAN
communication signal continuously for 2 seconds or
more with ignition switch ON.
In CAN communication system, any item (or items)
of the following listed below is malfunctioning:
• Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)
2015 Rogue NAM
DLK-112
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
DTC Logic
INFOID:0000000011377358
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011377359
1.
REPLACE BCM
When DTC U1010 is detected, replace BCM.
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
CONSULT Display
DTC Detection Condition
Possible Cause
CAN COMM CIRCUIT
[U1010]
BCM detected internal CAN communication circuit mal-
function.
BCM
2015 Rogue NAM
B2401 IGNITION POWER SUPPLY CIRCUIT
DLK-113
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
B2401 IGNITION POWER SUPPLY CIRCUIT
DTC Logic
INFOID:0000000011278823
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Operate automatic back door.
3. Check “Self Diagnostic Result” of “AUTO BACK DOOR” using CONSULT.
Is DTC detected?
YES
>> Refer to
DLK-113, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278824
1.
CHECK BCM OUTPUT SIGNAL
1. Select “IPDM E/R” using CONSULT.
2. Select “PUSH SW” in “Data Monitor”.
3. Check that the function operates normally according to the following conditions:
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
NO
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2401
IGN OPEN
Automatic back door control module cannot detect
ignition switch ON signal via CAN communication
with BCM.
• BCM
• Automatic back door control mod-
ule
• CAN communication system
Monitor item
Condition
Status
PUSH SW
Ignition switch
Pressed
Close
Not pressed
Open
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст