Nissan Rogue. Instruction — part 1109
SIDE CURTAIN AIR BAG MODULE
SR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000011279760
Removal and Installation
INFOID:0000000011279761
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Always work from the side of air bag module. Do not work in front of it.
• Do not use air tools or electric tools for servicing.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove the headlining. Refer to
INT-30, "Removal and Installation"
.
3. Disconnect the harness connector from the side curtain air bag
module.
CAUTION:
• For removing/installing the side curtain air bag module
harness connector, insert a thin screwdriver wrapped in
tape into the notch, lift the lock and remove the harness
connector as shown.
• Install the harness connector with the lock raised, and
push the lock into the harness connector as shown.
• After installing the harness connector, check that the lock
is pushed in securely.
ALHIA0362ZZ
1.
Side curtain air bag module
Front
PHIA0953J
SR-20
< REMOVAL AND INSTALLATION >
SIDE CURTAIN AIR BAG MODULE
4. Remove bolts, and side curtain air bag module.
CAUTION:
• Replace the side curtain air bag module if it has been dropped or sustained an impact.
• Do not strike the side curtain air bag module.
• Do not insert any foreign objects (screwdriver, etc.) into the side curtain air bag module.
• Do not disassemble the side curtain air bag module.
• Do not expose the side curtain air bag module to temperatures exceeding 90
°C (194 °F).
• Do not allow oil, grease, detergent or water to come in contact with the side curtain air bag mod-
ule.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Do not damage the harness while installing the side curtain air bag module.
• Make sure that the side curtain air bag module bracket supporting hooks are securely seated into
the body slots before releasing the side curtain air bag module during installation to avoid damaging
the side curtain air bag module.
• Make sure that the anti-twist stripe (black for RH side, blue for LH side) is visible along entire length
of side curtain air bag module.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
FRONT SIDE AIR BAG MODULE
SR-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT SIDE AIR BAG MODULE
Removal and Installation
INFOID:0000000011279762
The front side air bag module is part of the front seatback. For removal and installation of the front seatback,
refer to
.
SR-22
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Exploded View
INFOID:0000000011279763
Removal and Installation
INFOID:0000000011279764
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Do not use air tools or electric tools for servicing.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove front grille. Refer to
EXT-23, "Removal and Installation"
3. Remove crash zone sensor nut.
CAUTION:
Do not reuse the crash zone sensor nut.
4. Disconnect crash zone sensor harness connector, and remove crash zone sensor and bracket.
CAUTION:
• Replace the crash zone sensor if it has been dropped or sustained an impact.
• Do not strike the crash zone sensor.
• Replace the crash zone sensor if either the driver air bag or the front passenger air bag has been
deployed.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse the crash zone sensor nut.
• Do not damage the harness connector during installation.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
.
ALHIA0361ZZ
1.
Crash zone sensor
A.
Crash zone sensor harness
connector
B.
Bracket
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст