Nissan Rogue. Instruction — part 1110
SIDE AIR BAG (SATELLITE) SENSOR
SR-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE AIR BAG (SATELLITE) SENSOR
Exploded View
INFOID:0000000011279765
1.
Front door satellite sensor
2.
Front side air bag satellite sensor 3.
Rear side satellite sensor
ALHIA0349ZZ
SR-24
< REMOVAL AND INSTALLATION >
SIDE AIR BAG (SATELLITE) SENSOR
NOTE:
RH side shown, LH side similar.
Removal and Installation
INFOID:0000000011279766
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Do not use air tools or electric tools for servicing.
FRONT SIDE AIR BAG SATELLITE SENSOR
Removal
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove the center pillar lower finisher. Refer to
INT-22, "CENTER PILLAR LOWER FINISHER : Removal
3. Place aside the front seat belt retractor.
4. Remove the front side air bag satellite sensor nut.
CAUTION:
Do not reuse the front side air bag satellite sensor nut.
5. Disconnect the harness connector from the front side air bag satellite sensor and remove.
CAUTION:
• Replace the front side air bag satellite sensor if it has been dropped or sustained an impact.
• Do not strike the front side air bag satellite sensor.
Installation
Installation is in the reverse order of removal.
• Position the front side air bag satellite sensor using the pawl before tightening the nut to specification.
CAUTION:
• Do not reuse the front side air bag satellite sensor nut.
• Do not damage the harness connector during installation.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
.
REAR SIDE AIR BAG SATELLITE SENSOR
Removal
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove the luggage side lower finisher. Refer to
INT-34, "LUGGAGE SIDE LOWER FINISHER :
Removal and Installation - With Third Row Seat"
(WITH THIRD ROW SEAT),
LOWER FINISHER : Removal and Installation - With Third Row Seat"
(WITHOUT THIRD ROW SEAT).
3. Remove the rear side air bag satellite sensor bolt.
CAUTION:
Do not reuse the rear side air bag satellite sensor bolt.
4. Disconnect the harness connector from the rear side air bag satellite sensor and remove.
CAUTION:
• Replace the rear side air bag satellite sensor if it has been dropped or sustained an impact.
• Do not strike the rear side air bag satellite sensor.
Installation
Installation is in the reverse order of removal.
• Position the rear side air bag satellite sensor using the pawl before tightening the bolt to specification.
CAUTION:
A.
Satellite sensor harness connector
B
Bolt
C.
Nut
D.
Pawl
Front
SIDE AIR BAG (SATELLITE) SENSOR
SR-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Do not reuse the rear side air bag satellite sensor bolt.
• Do not damage the harness connector during installation.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
.
FRONT DOOR SATELLITE SENSOR
Removal
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove the front door finisher. Refer to
INT-15, "Removal and Installation"
3. Partially remove front door vapor barrier.
4. Remove the front door satellite sensor bolts.
CAUTION:
Do not reuse the front door satellite sensor bolts.
5. Disconnect the harness connector from the front door satellite sensor and remove.
CAUTION:
• Replace the front door satellite sensor if it has been dropped or sustained an impact.
• Do not strike the front door satellite sensor.
Installation
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse the front door satellite sensor bolts.
• Do not damage the harness connector during installation.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
.
SR-26
< REMOVAL AND INSTALLATION >
AIR BAG DIAGNOSIS SENSOR UNIT
AIR BAG DIAGNOSIS SENSOR UNIT
Exploded View
INFOID:0000000011279767
Removal and Installation
INFOID:0000000011279768
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Before disconnecting the air bag diagnosis sensor unit harness connectors, be sure to disconnect
each harness connector of the side curtain air bag modules, front seat belt pre-tensioner, and front
side air bag module, to prevent accidental air bag deployment by static electricity and seat belt pre-
tensioner operation.
• Do not use the air tools or electric tools for servicing.
• When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat-
est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the
air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags
and seat belt pre-tensioners in a collision resulting in serious personal injury or death.
REMOVAL
1. Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) or part
number using CONSULT.
2. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
3. Remove center console assembly. Refer to
IP-19, "Removal and Installation"
4. Disconnect the harness connectors for the following SRS components:
SR-19, "Removal and Installation"
(side curtain air bag modules),
SR-28, "Removal and Installation"
(front seat belt pre-tensioner) and
17, "Removal and Installation"
(front side air bag module).
5. Disconnect the harness connectors from the diagnosis sensor unit.
6. Remove bolt and nuts, then remove the air bag diagnosis sensor unit.
CAUTION:
• Do not reuse the air bag diagnosis sensor unit bolt and nuts.
• Replace the air bag diagnosis sensor unit if any SRS air bag has been deployed or if any front
seat belt pre-tensioner has been deployed.
AWHIA0599ZZ
1.
Diagnosis sensor unit
Front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст