Nissan Rogue. Instruction — part 329
DLK-158
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR SWITCH
BACK DOOR SWITCH
Component Function Check
INFOID:0000000011278868
1.
CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR SW-BK” in “Data Monitor”.
3. Check that the function operates normally according to the following conditions:
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Refer to
DLK-158, "Diagnosis Procedure (With Automatic Back Door)"
.
Diagnosis Procedure (With Automatic Back Door)
INFOID:0000000011278869
Regarding Wiring Diagram information, refer to
.
1.
CHECK BACK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect back door lock assembly connector.
3. Check signal between back door lock assembly harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between back door lock assembly harness connector and BCM harness connector.
3. Check continuity between back door lock assembly harness connector and ground.
Monitor item
Condition
Status
DOOR SW-BK
Back door
Open
On
Closed
Off
(+)
(–)
Signal
(Reference value)
Back door lock assembly
Connector
Terminal
D512
7
Ground
9.0 - 10.0 V
JPMIA0593GB
Back door lock assembly
BCM
Continuity
Connector
Terminal
Connector
Terminal
D512
7
B16
51
Yes
2015 Rogue NAM
BACK DOOR SWITCH
DLK-159
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR SWITCH GROUND CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR SWITCH
DLK-160, "Component Inspection (With Automatic Back Door)"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door lock assembly. Refer to
DLK-270, "DOOR LOCK : Removal and Installation"
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> Inspection End.
Diagnosis Procedure (Without Automatic Back Door)
INFOID:0000000011278870
Regarding Wiring Diagram information, refer to
.
1.
CHECK BACK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect back door lock assembly connector.
3. Check signal between back door lock assembly harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
Back door lock assembly
Ground
Continuity
Connector
Terminal
D512
7
No
Back door lock assembly
Ground
Continuity
Connector
Terminal
D512
8
Yes
(+)
(–)
Signal
(Reference value)
Back door lock assembly
Connector
Terminal
D508
3
Ground
9.0 - 10.0 V
JPMIA0593GB
2015 Rogue NAM
DLK-160
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR SWITCH
2.
CHECK BACK DOOR SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between back door lock assembly harness connector and BCM harness connector.
3. Check continuity between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR SWITCH GROUND CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR SWITCH
DLK-161, "Component Inspection (Without Automatic Back Door)"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door lock assembly. Refer to
DLK-270, "DOOR LOCK : Removal and Installation"
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> Inspection End.
Component Inspection (With Automatic Back Door)
INFOID:0000000011278871
1.
CHECK BACK DOOR SWITCH
1. Turn ignition switch OFF.
2. Disconnect back door lock assembly connector.
3. Check continuity between back door lock assembly terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace back door lock assembly. Refer to
DLK-270, "DOOR LOCK : Removal and Installation"
Back door lock assembly
BCM
Continuity
Connector
Terminal
Connector
Terminal
D508
3
B16
51
Yes
Back door lock assembly
Ground
Continuity
Connector
Terminal
D508
3
No
Back door lock assembly
Ground
Continuity
Connector
Terminal
D508
4
Yes
Back door lock assembly
Condition
Continuity
Terminal
7
8
Door switch
Pressed
No
Released
Yes
2015 Rogue NAM
BACK DOOR SWITCH
DLK-161
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Component Inspection (Without Automatic Back Door)
INFOID:0000000011278872
1.
CHECK BACK DOOR SWITCH
1. Turn ignition switch OFF.
2. Disconnect back door lock assembly connector.
3. Check continuity between back door lock assembly terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace back door lock assembly. Refer to
DLK-270, "DOOR LOCK : Removal and Installation"
Back door lock assembly
Condition
Continuity
Terminal
3
4
Door switch
Pressed
No
Released
Yes
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст