Nissan Rogue. Instruction — part 328
DLK-154
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
OUTSIDE KEY ANTENNA (REAR BUMPER)
OUTSIDE KEY ANTENNA (REAR BUMPER)
Component Function Check
INFOID:0000000011278863
1.
CHECK OUTSIDE KEY ANTENNA (REAR BUMPER)
1. Place the Intelligent Key into the detection area of the outside key antenna (rear bumper).
2. Press the door request switch (back door).
Does the door unlock?
YES
>> Inspection End.
NO
>> Refer to
DLK-154, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000011278864
Regarding Wiring Diagram information, refer to
.
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch OFF.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1. Disconnect BCM connector and outside key antenna (rear bumper) connector.
2. Check continuity between BCM harness connector and outside key antenna (rear bumper) harness con-
nector.
3. Check continuity between BCM harness connector and ground.
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
B16
61, 64
Ground
When the driver door
request switch is op-
erated with ignition
switch OFF.
When Intelligent Key
is in the antenna de-
tection area. (The dis-
tance between
Intelligent Key and
antenna: 80 cm or
less.)
When Intelligent Key
is not in the antenna
detection area. (The
distance between In-
telligent Key and an-
tenna: Approx. 2 m.)
JMKIA5955GB
JMKIA5954GB
BCM
Outside key antenna (rear bumper)
Continuity
Connector
Terminal
Connector
Terminal
B16
64
B76
1
Yes
61
2
2015 Rogue NAM
OUTSIDE KEY ANTENNA (REAR BUMPER)
DLK-155
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 2
1. Replace outside key antenna (rear bumper). (New antenna or other antenna)
2. Connect BCM and outside key antenna (rear bumper) connector.
3. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace outside key antenna (rear bumper). Refer to
DLK-279, "REAR BUMPER : Removal and
NO
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
BCM
Ground
Continuity
Connector
Terminal
B16
64
No
61
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
B16
61, 64
Ground
When the driver door
request switch is op-
erated with ignition
switch OFF.
When Intelligent Key
is in the antenna de-
tection area. (The dis-
tance between
Intelligent Key and
antenna: 80 cm or
less.)
When Intelligent Key
is not in the antenna
detection area. (The
distance between In-
telligent Key and an-
tenna: Approx. 2 m.)
JMKIA5955GB
JMKIA5954GB
2015 Rogue NAM
DLK-156
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR SWITCH
DOOR SWITCH
Component Function Check
INFOID:0000000011278865
1.
CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR SW-DR”, “DOOR SW-AS”, “DOOR SW-RL”, “DOOR SW-RR”, in “Data Monitor”.
3. Check that the function operates normally according to the following conditions:
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Refer to
DLK-156, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000011278866
Regarding Wiring Diagram information, refer to
.
1.
CHECK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect malfunctioning door switch connector.
3. Check signal between malfunctioning door switch harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between door switch harness connector and BCM harness connector.
Monitor item
Condition
Status
DOOR SW-DR
Front door LH
Open
On
Closed
Off
DOOR SW-AS
Front door RH
Open
On
Closed
Off
DOOR SW-RL
Rear door LH
Open
On
Closed
Off
DOOR SW-RR
Rear door RH
Open
On
Closed
Off
(+)
(–)
Signal
(Reference value)
Door switch
Connector
Terminal
Front LH
B71
3
Ground
7.0 - 8.0 V
Front RH
B141
Rear LH
B70
Rear RH
B142
PKIB4960J
2015 Rogue NAM
DOOR SWITCH
DLK-157
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Check continuity between door switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK DOOR SWITCH
DLK-157, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunctioning door switch. Refer to
DLK-276, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> Inspection End.
Component Inspection
INFOID:0000000011278867
1.
CHECK DOOR SWITCH
1. Turn ignition switch OFF.
2. Disconnect malfunctioning door switch connector.
3. Check continuity between door switch terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace malfunctioning door switch. Refer to
DLK-276, "Removal and Installation"
Door switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
Front LH
B71
3
B16
57
Yes
Front RH
B141
53
Rear LH
B70
52
Rear RH
B142
50
Door switch
Ground
Continuity
Connector
Terminal
Front LH
B71
3
No
Front RH
B141
Rear LH
B70
Rear RH
B142
Door switch
Condition
Continuity
Terminal
3
Ground contact is part of the
switch.
Door switch
Pressed
No
Released
Yes
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст