Nissan Rogue. Instruction — part 240
DAS
U1305 CONFIG UNFINISH
DAS-131
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
U1305 CONFIG UNFINISH
DTC Logic
INFOID:0000000011419764
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011419765
1.
PERFORM CONFIGURATION
When U1305 is detected, perform configuration of around view monitor control unit.
>> Refer to
AV-281, "CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT) : Work Pro-
CONSULT Display
DTC Detection Condition
Possible Cause
Non-completion of the configu-
ration
[U1305]
Configuration of around view monitor control unit
is incomplete.
Perform configuration of around view monitor
control unit.
DAS-132
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
U1308 CAMERA CONFIG
U1308 CAMERA CONFIG
DTC Logic
INFOID:0000000011277275
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011277276
1.
PERFORM AROUND VIEW MONITOR CAMERA CALIBRATION
When U1308 is detected, the rear view camera needs to be calibrated.
>> Calibrate the rear view camera. Refer to
.
CONSULT Display
DTC Detection Condition
Possible Cause
Rear camera judgement
[U1308]
Around view monitor control unit camera calibra-
tion is incomplete.
Perform Around view monitor control unit camera
calibration.
DAS
U1309 PUMP UNIT CURRENT
DAS-133
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
U1309 PUMP UNIT CURRENT
DTC Logic
INFOID:0000000011277277
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” of “AVM” using CONSULT.
Is DTC detected?
YES
>> Refer to
DAS-133, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011277278
Regarding Wiring Diagram information, refer to
.
1.
CHECK REAR VIEW CAMERA WASHER CONTROL UNIT POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between rear view camera washer control unit connector B67 and ground.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK REAR VIEW CAMERA WASHER CONTROL UNIT GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear view camera washer control unit connector.
3. Check continuity between rear view camera washer control unit connector B67 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK REAR VIEW CAMERA WASHER CONTROL UNIT CIRCUITS CONTINUITY
1. Disconnect around view monitor control unit connector M113.
2. Check continuity between around view monitor control unit connector M113 and rear view camera washer
control unit connector B67.
CONSULT Display
DTC Detection Condition
Possible Cause
PUMP UNIT CURRENT
[U1309]
Around view monitor control unit detects incorrect
pump current from rear view camera washer con-
trol unit.
• Harness
• Rear view camera washer control unit
• Around view monitor control unit
Rear view camera washer control unit
Ground
Voltage
Connector
Terminal
B67
12
—
Battery voltage
Rear view camera washer control unit
Ground
Continuity
Connector
Terminal
B67
5
—
Yes
DAS-134
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
U1309 PUMP UNIT CURRENT
3. Check continuity between around view monitor control unit connector M113 and ground.
Is inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK CONTINUITY REAR VIEW CAMERA WASHER CONTROL UNIT TO PUMP
1. Disconnect rear view camera air pump motor connector.
2. Check continuity between rear view camera washer control unit connector B67 and rear view camera air
pump motor connector B72.
3. Check for continuity between rear view camera washer control unit connector B67 and ground.
Is inspection result normal?
YES
>> Replace the rear view camera air pump motor. Refer to
DAS-178, "Removal and Installation"
.
NO
>> Repair or replace harness or connectors.
Around view monitor control unit
Rear view camera washer control unit
Continuity
Connector
Terminal
Connector
Terminal
M113
36
B67
8
Yes
37
6
38
7
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M113
36
—
No
38
Rear view camera washer control unit
Rear view camera air pump motor
Continuity
Connector
Terminal
Connector
Terminal
B67
1
B72
1
Yes
2
2
Rear view camera washer control unit
Ground
Continuity
Connector
Terminal
B67
1
—
No
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст