Nissan Rogue. Instruction — part 239
DAS
U1302 CAMERA POWER VOLT
DAS-127
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
8.
CHECK SIDE CAMERA LH POWER SUPPLY (CAMERA)
1. Turn ignition switch ON.
2. Check voltage between side camera LH connector D14 and ground.
Is the inspection result normal?
YES
>> Replace side camera LH. Refer to
DAS-171, "Removal and Installation"
.
NO
>> GO TO 9.
9.
CHECK SIDE CAMERA LH POWER SUPPLY (AROUND VIEW MONITOR CONTROL UNIT)
Check voltage between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace around view monitor control unit. Refer to
DAS-173, "Removal and Installation"
10.
CHECK SIDE CAMERA LH POWER SUPPLY CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector M114 and side camera LH connector.
3. Check continuity between around view monitor control unit connector M114 and side camera LH connec-
tor D14.
4. Check continuity between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> Replace side camera LH. Refer to
DAS-171, "Removal and Installation"
.
NO
>> Repair or replace harness or connectors.
11.
CHECK SIDE CAMERA RH POWER SUPPLY (CAMERA)
1. Turn ignition switch ON.
2. Check voltage between side camera RH connector D107 and ground.
Is the inspection result normal?
YES
>> Replace side camera RH. Refer to
DAS-171, "Removal and Installation"
NO
>> GO TO 12.
12.
CHECK SIDE CAMERA RH POWER SUPPLY (AROUND VIEW MONITOR CONTROL UNIT)
Side camera LH
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
D14
7
—
CAMERA switch is ON.
6.0 V
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M114
56
—
CAMERA switch is ON.
6.0 V
Around view monitor control unit
Side camera LH
Continuity
Connector
Terminal
Connector
Terminal
M114
56
D14
7
Yes
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M114
56
—
No
Side camera RH
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
D107
7
—
CAMERA switch is ON.
6.0 V
DAS-128
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
U1302 CAMERA POWER VOLT
Check voltage between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Replace around view monitor control unit. Refer to
DAS-173, "Removal and Installation"
.
13.
CHECK SIDE CAMERA RH POWER SUPPLY CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector M114 and side camera RH connector.
3. Check continuity between around view monitor control unit connector M114 and side camera RH connec-
tor D107.
4. Check continuity between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> Replace side camera RH. Refer to
DAS-171, "Removal and Installation"
.
NO
>> Repair or replace harness or connectors.
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M114
62
—
CAMERA switch is ON.
6.0 V
Around view monitor control unit
Side camera RH
Continuity
Connector
Terminal
Connector
Terminal
M114
62
D107
7
Yes
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M114
62
—
No
DAS
U1303 LED POWER SUPPLY VOLT
DAS-129
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
U1303 LED POWER SUPPLY VOLT
DTC Logic
INFOID:0000000011277269
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011277270
Regarding Wiring Diagram information, refer to
.
1.
CHECK BLIND SPOT WARNING POWER SUPPLY CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector M113 and blind spot warning indicators connec-
tors.
3. Check continuity between around view monitor control unit connector M113 and blind spot warning indica-
tors connectors D5 LH, D108 RH.
4. Check continuity between around view monitor control unit connector M113 and ground.
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
DAS-173, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
CONSULT Display
DTC Detection Condition
Possible Cause
LED supply power supply
voltage abnormality
[U1303]
Open or short in blind spot warning indicator pow-
er supply circuit.
• Harness or connectors.
• Around view monitor control unit.
Around view monitor control unit
Blind spot warning indicator
Continuity
Connector
Terminal
Connector
Terminal
M113
7
D5 LH
1
Yes
8
D108 RH
1
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M113
7
—
No
8
DAS-130
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
U1304 CAMERA IMAGE CALIBRATION
U1304 CAMERA IMAGE CALIBRATION
DTC Logic
INFOID:0000000011419762
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011419763
1.
PERFORM CALIBRATION
When U1304 is detected, perform calibration of camera image.
>> Refer to
AV-284, "CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Work Proce-
.
CONSULT Display
DTC Detection Condition
Possible Cause
Non-completion of the calibra-
tion
[U1304]
Camera image calibration is incomplete.
Perform calibration of camera image.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст