Nissan Rogue. Instruction — part 567
EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
8. Remove the air fuel ratio (A/F) sensor 1 using Tool, (if necessary).
CAUTION:
• Clean exhaust manifold and three way catalyst port securing air fuel ratio (A/F) sensor 1 with
anti-seize lubricant, or equivalent.
• Be careful not to damage air fuel ratio (A/F) sensor.
• Discard any air fuel ratio (A/F) sensor which has been dropped from a height of more than 0.5 m
(19.7 in) onto a hard surface such as a concrete floor; replace with a new one.
9. Detach front exhaust tube from exhaust manifold and three way catalyst. Discard the gasket. Refer to
.
10. Remove the exhaust manifold cover (upper).
11. Loosen the exhaust manifold and three way catalyst nuts in the
reverse order as shown.
12. Remove exhaust manifold and three way catalyst.
13. Remove exhaust manifold and three way catalyst gasket.
14. Remove the exhaust manifold cover (lower front) (if necessary).
15. Remove the exhaust manifold cover (lower rear) (if necessary).
INSPECTION AFTER REMOVAL
Surface Distortion
• Check the flatness of exhaust manifold and three way catalyst
using suitable tools (A/B).
NOTE:
Place the suitable tool (A) diagonally and measure in several loca-
tions.
INSTALLATION
Exhaust Manifold
1. Install studs in cylinder head and exhaust manifold (if removed). Then tighten to specification.
CAUTION:
Do not reuse cylinder head gasket or exhaust manifold studs.
Tool numbers
: KV991J0050 (J-44626)
AWBIA1909ZZ
Limit
: 0.3 mm (0.012 in)
ALBIA0828GB
EM-34
< REMOVAL AND INSTALLATION >
EXHAUST MANIFOLD AND THREE WAY CATALYST
2. Install exhaust manifold cover (lower rear) (if removed) and
bolts. Then tighten the bolts to specification in the numerical
order shown.
CAUTION:
Do not reuse bolts.
3. Install the exhaust manifold and three way catalyst, along with
the exhaust manifold and three way catalyst gasket. Then
tighten the nuts to specification in the numerical order shown.
CAUTION:
Do not reuse gasket.
4. Install the exhaust manifold cover (lower front) and bolts. Then
tighten the bolts to specification in the numerical order shown.
CAUTION:
Do not reuse bolts.
5. Clean exhaust manifold and three way catalyst port securing air fuel ratio (A/F) sensor 1 with Tool.
6. Install the air fuel ratio (A/F) sensor 1 using Tool and tighten to specification.
CAUTION:
• Clean exhaust manifold and three way catalyst port securing air fuel ratio (A/F) sensor 1 with
anti-seize lubricant, or equivalent.
• Be careful not to damage air fuel ratio (A/F) sensor 1.
• Discard any air fuel ratio (A/F) sensor 1 which has been dropped from a height of more than 0.5
m (19.7 in) onto a hard surface such as a concrete floor; replace with a new one.
• Do not over-tighten the air fuel ratio (A/F) sensor 1. Doing so may cause damage to the air fuel
ratio (A/F) sensor 1, resulting in a malfunction and the MIL coming on.
ALBIA0887GB
: Front
AWBIA1386ZZ
ALBIA0889GB
Tool numbers
: (J-43897-18)
Tool numbers
: KV991J0050 (J-44626)
EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
7. Install the exhaust manifold cover (upper). Then tighten the bolts
to specification in the numerical order shown.
CAUTION:
Do not reuse bolts.
ALBIA0888GB
EM-36
< REMOVAL AND INSTALLATION >
OIL PAN AND OIL STRAINER
OIL PAN AND OIL STRAINER
Exploded View
INFOID:0000000011358721
Removal and Installation
INFOID:0000000011279953
REMOVAL
WARNING:
To avoid danger of being scalded, do not drain engine oil when engine is hot.
1. Drain engine oil. Refer to
.
2. Remove the oil filter. Refer to
LU-10, "Removal and Installation"
.
1.
Oil pan (upper)
2.
Oil filter
3.
Front cover
4.
O-ring
5.
Oil strainer
6.
O-ring
7.
Oil pan (lower)
8.
Washer
9.
Drain plug
10.
Rear cover plate
11. O-ring
12. Oil level gauge guide
13.
Oil level gauge
A.
To oil pan (lower)
AWBIA2237ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст