Nissan Rogue. Instruction — part 568
OIL PAN AND OIL STRAINER
EM-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
3. Remove fender protector (RH). Refer to
EXT-28, "FENDER PROTECTOR : Removal and Installation"
.
4. Remove the front driveshaft (RH). Refer to
FAX-23, "Removal and Installation (RH)"
.
5. Remove the front exhaust tube and gaskets. Refer to
6. Remove bolt (A) securing oil level gauge (2).
7. Remove oil level gauge (1), oil level gauge guide (2), and O-ring
(3).
8. Remove the power steering gear bolts and support the power steering gear. Refer to
9. Remove the rear engine mount torque rod bracket. Refer to
10. Remove the front suspension member for clearance to remove the oil pan. Refer to
11. On models equipped with AWD, remove transfer assembly. Refer to
DLN-71, "Removal and Installation"
.
12. Disconnect the A/C compressor harness connector.
13. Remove the A/C compressor bolts, position the A/C compressor aside and support. Refer to
14. Remove the lower oil pan bolts in the reverse order as shown.
15. Remove the lower oil pan using Tool (A).
CAUTION:
Be careful not to damage the mating surfaces.
NOTE:
In areas where the cutter is difficult to use, use a plastic hammer
to lightly tap (1) the cutter where the liquid gasket is applied. Use
a plastic hammer to slide (2) the cutter by tapping on the side.
AWBIA1986ZZ
ALBIA0830GB
Tool number
: KV10111100 (J-37228)
AWBIA1249GB
EM-38
< REMOVAL AND INSTALLATION >
OIL PAN AND OIL STRAINER
16. Remove the oil strainer bolts in the reverse order as shown then
remove the oil strainer.
17. Remove rear cover plate and engine-to transaxle bolts.
18. Loosen the upper oil pan bolts in the order shown.
19. Remove upper oil pan using Tool (A).
• Remove the three O-rings from the upper oil pan and front
cover.
CAUTION:
Be careful not to damage the mating surfaces.
NOTE:
In areas where the cutter is difficult to use, use a plastic hammer
to lightly tap (1) the cutter where the liquid gasket is applied. Use
a plastic hammer to slide (2) the cutter by tapping on the side.
INSPECTION AFTER REMOVAL
Clean the oil strainer screen to remove any foreign material.
INSTALLATION
1. Apply Genuine Silicone RTV Sealant or equivalent to the upper
oil pan at the specified sealant bead diameter (A) as shown.
Refer to
GI-22, "Recommended Chemical Products and Seal-
.
CAUTION:
• Be sure liquid gasket application surface is free from dust, grease, and water.
• Install two new O-rings in the upper oil pan and a new O-ring in the front cover.
• Do not reuse O-rings.
AWBIA1382ZZ
ALBIA0832GB
Tool number
: KV10111100 (J-37228)
AWBIA1249GB
Sealant bead
diameter (A)
: 4.0 - 5.0 mm (0.157 - 0.197 in)
AWBIA1987ZZ
OIL PAN AND OIL STRAINER
EM-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Be sure to apply liquid gasket to the outside of bolt holes
1, 2, and 4.
• Be sure to apply liquid gasket without breaks or overlap.
• Installation should be done within 5 minutes after applying liquid gasket.
• Do not fill the engine with engine oil for at least 30 minutes after the components are installed to
allow the liquid gasket to cure.
2. Install the upper oil pan to the block and tighten the upper oil pan bolts to specification in the order shown.
CAUTION:
Install upper oil pan bolts in the same position from which
they were removed.
3. Apply Genuine Silicone RTV Sealant or equivalent to the lower
oil pan at the specified sealant bead diameter (A) as shown.
Refer to
GI-22, "Recommended Chemical Products and Seal-
CAUTION:
• Be sure liquid gasket application surface is free from
dust, grease, and water.
• Be sure to apply liquid gasket to the inside of all bolt
holes.
• Be sure to apply liquid gasket without breaks or overlap.
• Installation should be done within 5 minutes after apply-
ing liquid gasket.
• Do not fill the engine with engine oil for at least 30 minutes after the components are installed to
allow the liquid gasket to cure.
4. Install the lower oil pan to the upper oil pan and tighten the lower oil pan bolts to specification in the
numerical order shown.
CAUTION:
ALBIA0832GB
All bolts except 18 and 19 : 21.6 N·m (2.2 kg-m, 16 ft-lb)
Bolts 18 and 19
: 8.8 N·m (0.90 kg-m, 78 in-lb)
ALBIA0832GB
Sealant bead
diameter (A)
: 4.0 - 5.0 mm (0.157 - 0.197 in)
ALBIA0834GB
EM-40
< REMOVAL AND INSTALLATION >
OIL PAN AND OIL STRAINER
Install new drain plug washer.
5. Install oil level gauge (1), oil level gauge guide (2), and O-ring (3).
CAUTION:
Do not reuse oil level gauge guide O-ring.
6. Installation of the remaining components is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
Check for engine oil leaks with the engine at operating temperature and running at idle. Refer to
ALBIA0830GB
Bolt (A)
: 21.6 N·m (2.2 kg-m, 16 ft-lb)
AWBIA1986ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст