Nissan Rogue. Instruction — part 698
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
• Quick connector (1) can be disconnected when the tabs
(F) are depressed completely. Do not twist it more than
necessary.
• Do not use any tools to disconnected quick connector.
• Keep resin tube (C) away from heat. Be especially care-
ful when welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, etc. from
getting on resin tube.
• Do not bend or twist resin tube during installation and
disconnection.
• Do not remove the remaining retainer (2) on hard tube
(or the equivalent) (A) except when resin tube or retainer
is replaced.
• When resin tube or hard tube (or the equivalent) is
replaced, also replace retainer with new one.
• To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags (A) or something similar.
9. Remove the lock ring from the fuel level sensor, fuel filter, and fuel pump assembly.
• Remove the lock ring using Tool (A).
(B)
: Connection (cross-section)
(D)
: To under floor fuel line
(E)
: To fuel tank
(G)
: Disconnection
JPBIA0130ZZ
JPBIA0135ZZ
Tool number
: ( — ) J-45747 (shown)
: KV101207S0 ( — )
: Front
ALBIA1195ZZ
FL-8
< REMOVAL AND INSTALLATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
• Prior to removal, observe the alignment between the fuel level
sensor, fuel filter, and fuel pump assembly tabs (A) and the
matching marks (C) on the fuel tank as shown. This alignment
is necessary for proper installation.
10. Raise fuel level sensor unit, fuel filter and fuel pump assembly
(1), and disconnect fuel tube and harness connector.
CAUTION:
• Do not bend float arm during removal.
• Do not pollute the inside by residue fuel. Draw out avoid-
ing inclination by supporting with a cloth.
• Do not cause impacts such by dropping when handling
components.
Sub Fuel Level Sensor Assembly
1. Remove fuel level sensor unit, fuel filter and fuel pump assembly.
2. Remove second row seat (LH). Refer to
SE-39, "Removal and Installation"
.
3. Remove inspection hole cover.
• Using a suitable, remove it by turning clips clockwise by 90 degrees.
4. Remove the lock ring from the fuel level sensor, fuel filter, and
sub fuel level assembly.
5. Remove sub fuel level sensor assembly (1).
CAUTION:
• Do not disassemble a fuel tube (2) from sub fuel sensor
assembly.
• Do not bend float arm during removal.
• Do not pollute the inside by residue fuel. Draw out avoid-
ing inclination by supporting with a cloth.
• Do not cause impacts such by dropping when handling
components.
NOTE:
Tie a gasoline-resistance rope to a tip of the tube. Draw (
) and
leave the rope to the fuel tank side so that the rope can be the
guide for installation.
INSTALLATION
Installation is in the reverse order of removal.
• Install O-ring to fuel tank without any twist.
(B)
: Retainer mounting pawl
JPBIA4665ZZ
PBIC3780E
Tool number
: ( — ) J-45747 (shown)
: KV101207S0 ( — )
: Front
AWBIA1846ZZ
JPBIA0823ZZ
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
CAUTION:
Do not reuse O-ring.
• Using the rope left on the fuel tank side at removal, run the fuel tube inside the fuel tank to install the sub fuel
level sensor assembly to the fuel tank.
CAUTION:
• Do not bend float arm during installation.
• To install, fuel tube (1) must run to the front (
) of the vehicle to avoid the interference with the
float arm (2), as shown.
• Align the tabs (A) of the fuel level sensor unit, fuel filter and fuel
pump assembly (1) as shown.
NOTE:
Fuel level sensor unit, fuel filter and fuel pump assembly side of
fuel tank shown.
• Check the connection for damage or any foreign materials.
• Align the connector with the tube, then insert the connector straight into the tube until a “click” sound is
heard.
• After connecting, check that the connection is secured with following procedures.
- Visually confirm that the two tabs are connected to the connector.
- Pull (A) the tube and the connector to check that they are securely
connected.
• Before installing inspection hole cover, check that the connecting
part has no fuel leaks. Refer to
• Install inspection hole covers with the front mark (arrow) facing
front.
• Lock clips by turning counterclockwise.
Inspection
INFOID:0000000011279615
INSPECTION AFTER INSTALLATION
AWBIA1841ZZ
: Front
JPBIA1268ZZ
JPBIA0140ZZ
FL-10
< REMOVAL AND INSTALLATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Use the following procedure to check for fuel leaks.
1. Turn ignition switch “ON” (with engine stopped), then check connections for leaks by applying fuel pres-
sure to fuel piping.
2. Start engine. Then let it idle and check that there is no fuel leaks at the fuel system connections.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст