Nissan Rogue. Instruction — part 697
PREPARATION
FL-3
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000011279610
The actual shape of the tools may differ from those illustrated here
Tool number
(TechMate No.)
Tool name
Description
KV101207S0
( — )
Unified fuel lock ring wrench
Removing and installing fuel tank lock ring
—
(J-45747)
Fuel tank lock ring wrench
JPBIA6384ZZ
JSBIA1952ZZ
FL-4
< PERIODIC MAINTENANCE >
FUEL SYSTEM
PERIODIC MAINTENANCE
FUEL SYSTEM
Inspection
INFOID:0000000011279611
Inspect fuel lines, fuel filler cap, and fuel tank for improper attach-
ment, leaks, cracks, damage, loose connections, chafing or deterio-
ration.
If necessary, repair or replace damaged parts.
Quick Connector
INFOID:0000000011279612
CAUTION:
• After connecting fuel tube quick connectors, check that quick connectors are secure.
• Ensure that connector and resin tube never contact any adjacent parts.
• Quick connector (1) can be disconnected when the tabs (F)
are depressed completely. Do not twist it more than neces-
sary.
• Do not use any tools to disconnected quick connector.
• Keep resin tube (C) away from heat. Be especially careful
when welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, etc. from get-
ting on resin tube.
• Do not bend or twist resin tube during installation and discon-
nection.
• Do not remove the remaining retainer (2) on hard tube (or the
equivalent) (A) except when resin tube or retainer is replaced.
• When resin tube or hard tube (or the equivalent) is replaced,
also replace retainer with new one.
• To keep the connecting portion clean and to avoid damage
and foreign materials, cover them completely with plastic
bags (A) or something similar.
(A)
: Engine
(B)
: Fuel line
(C)
: Fuel tank
JPBIA0129ZZ
(B)
: Connection (cross-section)
(D)
: To under floor fuel line
(E)
: To fuel tank
(G)
: Disconnection
JPBIA0130ZZ
JPBIA0135ZZ
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
REMOVAL AND INSTALLATION
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Exploded View
INFOID:0000000011279613
Removal and Installation
INFOID:0000000011279614
WARNING:
Be sure to read “General Precautions” before working on the fuel system. Refer to
.
CAUTION:
Do not remove or disassemble parts unless instructed as shown.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
Fuel Level Sensor Unit, Fuel Filter And Fuel Pump Assembly
1. Lock ring
2. O-ring
3. Fuel filter and fuel pump assembly
4. Fuel level sensor and fuel tank temperature sensor 5. Sub fuel level sensor assembly 6. Fuel tank
Front
AWBIA2278ZZ
FL-6
< REMOVAL AND INSTALLATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
1. Check the fuel level with the vehicle on a level surface. If the fuel
gauge indicates more than the level as shown (1/2 full), drain
the fuel from the fuel tank until the fuel gauge indicates a level at
or below as shown (1/2 full).
• In case the fuel pump does not operate, use the following pro-
cedure.
a. Insert fuel tubing of less than 25mm (0.98in) diameter into the
fuel filler tube through the fuel filler opening to drain fuel from the
fuel filler tube.
b. Disconnect the fuel filler hose from the fuel filler tube.
c.
Insert fuel tubing into the fuel tank through the fuel filler hose to
drain fuel from the fuel tank.
• As a guide, the fuel level reaches or is less than the level on the fuel gauge as shown, when approxi-
mately 27.5 (7-1/4 US gal, 6 Imp gal) of fuel is drained from a full fuel tank.
2. Release the fuel pressure from the fuel lines. Refer to
.
3. Open fuel filler lid.
4. Open fuel filler cap and release the pressure inside the fuel tank.
5. Disconnect negative battery terminal. Refer to
PG-78, "Removal and Installation (Battery)"
.
6. Remove second row seat (RH). Refer to
SE-39, "Removal and Installation"
7. Turn the four retainers 90 degrees to disengage the clips and remove the fuel pump inspection hole cover.
CAUTION:
Cover the immediate area surrounding the fuel pump inspection hole cover with plastic to avoid
gasoline damage to carpet.
8. Disconnect harness connector (A) and quick connector (B).
Disconnect quick connector as follows:
• Hold the sides of connector, press tabs and pull out fuel feed
tube.
•
If quick connector sticks to tube of main fuel level sensor unit, push and pull quick connectors several
times until they start to move. Then disconnect them by pulling.
CAUTION:
: Front
ALBIA0787ZZ
JPBIA1266ZZ
(A)
: Pull
(B)
: Push in tabs
JPBIA0134ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст