Nissan Rogue. Instruction — part 1044
SE-42
< REMOVAL AND INSTALLATION >
THIRD ROW SEATS
THIRD ROW SEATS
Exploded View
INFOID:0000000011280457
1.
Seatback board (RH)
2.
Seatback trim (RH)
3.
Seatback pad (RH)
4.
Seat cushion trim (RH)
5.
Seat cushion pad (RH)
6.
Seat cushion silencer (LH/RH)
7.
Seat hinge finisher (RH)
8.
Gas stay
9.
Bolt cover (RH)
AWJIA1319ZZ
THIRD ROW SEATS
SE-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Removal and Installation
INFOID:0000000011280458
CAUTION:
During removal and installation, an assistant is required to protect against injury or damage.
REMOVAL
1. Using a suitable tool release pawls and remove front bolt covers
RH (2) and LH (1).
2. Insert a suitable tool (A) through both U wires (B) of third row
seat legs (1) (LH/RH).
WARNING:
Do not remove seat front bolts without inserting a suitable
tool through both U wires to protect against personal injury.
3. Remove the seat front bolts (A).
4. Fold the seatback to the flat position and open back door.
10. Seat belt buckle (RH)
11. Seat belt buckle (LH)
12. Bolt cover (LH)
13. Stopper pin
14. Seat frame support
15. Seat hinge finisher (LH)
16. Seat striker (LH/RH)
17. Seat striker finisher (LH/RH)
18. Seatback pull strap (LH/RH)
19. Seatback frame (LH)
20. Headrest (LH/RH)
21. Third row seat cross member
22. Third row seat cross member fin-
isher (LH)
23. Third row seat cross member
finisher (center)
24. Third row seat cross member fin-
isher (RH)
25. Third row luggage floor
26. Seatback board (LH)
27. Seatback trim (LH)
28. Seatback pad (LH)
29. Seat cushion trim (LH)
30. Seat cushion pad (LH)
31. Seat frame finisher (center)
32. Seat cushion frame (LH)
33. Seat cushion frame (RH))
34. Headrest holder (locked)
35. Headrest holder (free)
36. Seatback frame (RH)
Clip
Pawl
ALJIA1423ZZ
ALJIA1479ZZ
ALJIA1424ZZ
SE-44
< REMOVAL AND INSTALLATION >
THIRD ROW SEATS
5. Release seat latches by pulling straps (A) rearward, then lift seat
from seat strikers (LH/RH) and remove.
INSTALLATION
Installation is in the reverse order of removal.
WARNING:
Do not remove suitable tool from U wires before installing seat front bolts or personal injury may
occur.
NOTE:
1. Two people are required to position the seat so the seat latches are over the seat striker locations.
2. Place rear seat legs on strikers, make sure to latch.
3. Check that the rear seat latch and striker do not interfere, then tighten bolts to specification. Refer to
Third Row Seat Cross Member
INFOID:0000000011280459
REMOVAL
1. Remove the third row seat. Refer to
SE-43, "Removal and Installation"
.
2. Remove screws (A) and third row seat cross member finishers
(1, 2, 3).
ALJIA1425ZZ
ALJIA1427ZZ
THIRD ROW SEATS
SE-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
3. Release third row luggage board outer clips (A) and inner clips
(B) using a suitable tool.
4. Release third row luggage board retainer strap clips (A) (LH/RH)
using a suitable tool and remove third row luggage board.
5. Remove bolts and remove third row seat cross member.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• Tighten the third row seat cross member to specification. Refer to
ALJIA1429ZZ
ALJIA1430ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст