Nissan Rogue. Instruction — part 1048
SE-58
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
iii. Release clips (A) from seat cushion frame as shown (
).
:Clip
iv. Release remaining pawls then remove seat cushion outer fin-
isher (LH) (1).
: Pawl
b. For power seat:
i.
Remove the seat cushion outer finisher (LH) (1).
ii.
Remove seat slide knob (2), seat recline knob (3) and seat lum-
bar knob (4), then release clips (A) from seat frame (5), as
shown (
).
:Clip
iii. Release pawls and remove.
: Pawl
iv. Disconnect harness connectors from the power seat switch and lumbar support switch.
AWJIA1542ZZ
AWJIA1566ZZ
FRONT SEAT
SE-59
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
8. Release pawls and clips, and remove seat cushion outer finisher
(RH) in the direction shown (
).
: Pawl
: Metal clip
:Clip
9. Release clips and remove side air bag module harness from seat frame.
NOTE:
Take note of harness routing and attachment location for correct installation.
10. Disconnect the harness connector from lumbar support motor (if equipped) and release harness from
seatback assembly.
NOTE:
Take note of harness routing and attachment location for correct installation.
11. Disconnect the harness connector for the front seat heater (if equipped).
NOTE:
Take note of harness routing and attachment location for correct installation.
12. Remove seatback trim and pad.
13. Release fastener and remove hog rings, then separate seatback
trim from seatback pad.
NOTE:
Remove all pieces of hog rings and discard them.
: Hog ring
14. Remove screws (A) on both sides of the seatback frame (1).
CAUTION:
Do not reuse seatback frame screws. Replace with new
ones.
ASSEMBLY
ALJIA1442ZZ
ALJIA1432ZZ
ALJIA0969ZZ
SE-60
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
• First tighten screws by hand in the order shown.
• Tighten the seatback assembly screws to specification. Refer to
.
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
back trim and seatback pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Make sure hook fastener is pressed into place after seatback trim
is assembled.
• Smooth out all wrinkles during assembly.
CAUTION:
• Do not reuse seatback frame bolts, replace with new ones.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system malfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to
.
Seat Cushion
INFOID:0000000011280468
DISASSEMBLY
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seat cushion repair. It can lead
to personal injury if the side air bag module should accidentally deploy.
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least
three minutes.
• Always work from the side or back of the seatback assembly, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
NOTE:
Front seat (LH) shown, front seat (RH) similar.
1. Remove the front seat driver side or front seat passenger side. Refer to
(DRIVER SIDE),
SE-35, "PASSENGER SIDE : Removal and Installation"
(PASSENGER
SIDE).
ALJIA1443ZZ
PIIB3356J
FRONT SEAT
SE-61
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
2. Remove seat cushion outer finisher (LH).
a. For instruction seat:
i.
Remove snap ring (1) as shown (
) using a suitable tool, then
remove the recline lever (2).
ii.
Release pawl and remove lift lever.
iii. Release clips (A) from seat cushion frame as shown (
).
:Clip
iv. Release remaining pawls then remove seat cushion outer fin-
isher (LH) (1).
: Pawl
b. For power seat:
i.
Remove the seat cushion outer finisher (LH) (1).
ii.
Remove seat slide knob (2), seat recline knob (3) and seat lum-
bar knob (4), then release clips (A) from seat frame (5), as
shown (
).
:Clip
iii. Release pawls and remove.
: Pawl
AWJIA1562ZZ
AWJIA1542ZZ
AWJIA1566ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст